Software V01.31
List of featuresOctober 2011Manual
INST / OPT/ PRGCNC 8055 FL Engraving model
CNC 8055
CNC 8055i
·12·Version history
8055 power FL-M的最新操作手册
SAFETY CONDITIONS
Read the following safety measures in order to prevent harming people or damage to this product and thoseproducts connected to it.
This unit may only be repaired by authorized personnel at Fagor Automation.
Fagor Automation shall not be held responsible of any physical damage or defective unit resulting from notcomplying with these basic safety regulations.
PRECAUTIONS AGAINST PERSONAL DAMAGE
Interconnection of modules.
Use the connection cables provided with the unit.
Use proper Mains AC power cables
To avoid risks, use only the Mains AC cables recommended for this unit.
Avoid electrical overloads.
In order to avoid electrical discharges and fire hazards, do not apply electrical voltage outside the rangeselected on the rear panel of the central unit.
Ground connection.
In order to avoid electrical discharges, connect the ground terminals of all the modules to the mainground terminal. Before connecting the inputs and outputs of this unit, make sure that all the groundingconnections are properly made.
Before powering the unit up, make sure that it is connected to ground.
In order to avoid electrical discharges, make sure that all the grounding connections are properly made. Do not work in humid environments.
In order to avoid electrical discharges, always work under 90% of relative humidity (non-condensing)and 45 ºC (113º F).
Do not work in explosive environments.
In order to avoid risks or damages, do no work in explosive environments.
CNC 8055CNC 8055i
·13·
8055 power FL-M的最新操作手册
snoitidnoc ytefaS
CNC 8055
CNC 8055i
·14·PRECAUTIONS AGAINST PRODUCT DAMAGE Working environment.This unit is ready to be used in industrial environments complying with the directives and regulationseffective in the European Community.Fagor Automation shall not be held responsible for any damage suffered or caused when installed inother environments (residential or homes). Install this unit in the proper place.It is recommended, whenever possible, to install the CNC away from coolants, chemical product, blows,etc. that could damage it.This unit complies with the European directives on electromagnetic compatibility. Nevertheless, it isrecommended to keep it away from sources of electromagnetic disturbance such as: Powerful loads connected to the same AC power line as this equipment. Nearby portable transmitters (Radio-telephones, Ham radio transmitters). Nearby radio/TV transmitters. Nearby arc welding machines. Nearby High Voltage power lines. Etc. Enclosures.The manufacturer is responsible of assuring that the enclosure involving the equipment meets all thecurrently effective directives of the European Community. Avoid disturbances coming from the machine tool.The machine-tool must have all the interference generating elements (relay coils, contactors, motors,etc.) uncoupled. DC relay coils. Diode type 1N4000. AC relay coils. RC connected as close to the coils as possible with approximate values of R=220 1 W and C=0,2 µF / 600 V. AC motors. RC connected between phases, with values of R=300 / 6 W and C=0,47 µF / 600 V. Use the proper power e an external regulated 24 Vdc power supply for the inputs and outputs. Grounding of the power supply.The zero volt point of the external power supply must be connected to the main ground point of themachine. Analog inputs and outputs connection.It is recommended to connect them using shielded cables and connecting their shields (mesh) to thecorresponding pin. Ambient conditions.The working temperature must be between +5 ºC and +40 ºC (41ºF and 104º F)The storage temperature must be between -25 ºC and +70 ºC. (-13 ºF and 158 ºF) Monitor enclosure (8055) or central unit (8055i).Guarantee the required gaps between the monitor or the central unit and each wall of the e a DC fan to improve enclosure ventilation. Power switch.This power switch must be mounted in such a way that it is easily accessed and at a distance between0.7 meters (27.5 inches) and 1.7 meters (5.5ft) off the floor.
8055 power FL-M的最新操作手册
PROTECTIONS OF THE UNIT ITSELF (8055)
"Axes" and "Inputs/Outputs" modules.
All the digital inputs and outputs have galvanic isolation via optocouplers between the CNC circuitryand the outside.
They are protected by an external fast fuse (F) of 3.15 A 250V against overvoltage of the external powersupply (over 33 Vdc) and against reverse connection of the power supply.
Monitor.Safety conditionsThe type of protection fuse depends on the type of monitor. See identification label of the unit itself.PROTECTIONS OF THE UNIT ITSELF (8055I)
Central Unit.