Running sccheck ... done All sccheck tests passed.
Hit ENTER to continue: [Enter]
>>> Cluster Nodes <<<
This release of Sun Cluster supports a total of up to 8 nodes.
Please list the names of the other nodes planned for the initial cluster configuration. List one node name per line. When finished, type Control-D:
Node name: igwb1 Node name: igwb2
Node name （Ctrl-D to finish): ^D （CTRL + D)
This is the complete list of nodes:
igwb1 igwb2
Is it correct （yes/no) [yes]? [Enter]
>>> Authenticating Requests to Add Nodes <<<
Once the first node establishes itself as a single node cluster, other nodes attempting to add themselves to the cluster configuration must be found on the list of nodes you just provided. The list can be modified once the cluster has been established using scconf（1M) or other tools.
4
By default, nodes are not securely authenticated as they attempt to add themselves to the cluster configuration. This is generally
considered adequate, since nodes which are not physically connected to the private cluster interconnect will never be able to actually join the cluster. However, DES authentication is available. If DES authentication is selected, you must configure all necessary encryption keys before any node will be allowed to join the cluster （see keyserv（1M), publickey（4)).
Do you need to use DES authentication （yes/no) [no]? [Enter]
>>> Network Address for the Cluster Transport <<<
The private cluster transport uses a default network address of 172.16.0.0. But, if this network address is already in use elsewhere within your enterprise, you may need to select another address from the range of recommended private addresses （see RFC 1597 for details).
If you do select another network address, please bear in mind that the Sun Clustering software requires that the rightmost two octets always be zero.
The default netmask is 255.255.0.0; you may select another netmask, as long as it minimally masks all bits given in the network address and does not contain any \
Is it okay to accept the default network address （yes/no) [yes]? [Enter]
Is it okay to accept the default netmask （yes/no) [yes]? [Enter]
5
>>> Point-to-Point Cables <<<
The two nodes of a two-node cluster may use a directly-connected interconnect. That is, no cluster transport junctions are configured. However, when there are greater than two nodes, this interactive form of scinstall assumes that there will be exactly two cluster transport junctions.
Does this two-node cluster use transport junctions （yes/no) [yes]? no
>>> Cluster Transport Adapters and Cables <<<
You must configure at least two transport adapters on each node which serve as connection points to the private cluster transport. More than two connection points are allowed, but this interactive form of scinstall assumes exactly two.
Note that interactive scinstall does not allow you to specify any special transport adapter properties settings. If your adapters have special properties which must be set, you may need to use non-interactive scinstall by specifying a complete set of command line options. For more information, please refer to the man pages for your adapters in the scconf_transp_adap family of man pages （e.g., scconf_transp_adap_eri（1M)).
Hit ENTER to continue: [Enter]
Select the first cluster transport adapter to use: 1) ce0 2) ce5 3) Other Option: 1
6
（Notes : 请选择 \，即机器的内置网卡)
? 说明：
1）由于机器配臵不同，这里显示的网卡可能会不一致，请根据实际情况选择正确的网卡。
2）心跳采用原则是：小型机的内臵网口（在Netra440为ce0和ce5）
Adapter \
Searching for unexpected network traffic on \ Verification completed. No traffic was detected over a 10 second sample period.
All transport adapters support the \ adapters are supported only with the \ adapter types may support other types of transport. For more information on which transports are supported with which adapters, please refer to the scconf_transp_adap family of man pages （scconf_transp_adap_eri（1M), ...).
The \ Select the second cluster transport adapter to use: 1) ce5 2) Other Option: 1
（Notes : 请选择\，即机器另外一块单口网卡)
? 说明：
由于机器配臵不同，这里显示的网卡可能会不一致，请根据实际情况选择正确的网卡。
Adapter \
Searching for unexpected network traffic on \ Verification completed. No traffic was detected over a 10 second sample period.
>>> Global Devices File System <<<
Each node in the cluster must have a local file system mounted on
7
/global/.devices/node@
already-mounted file system or raw disk partition at this time. This file system or partition should be at least 100 MB in size.
If an already-mounted file system is used, the file system must be empty. If a raw disk partition is used, a new file system will be created for you.
The default is to use /globaldevices.
Is it okay to use this default （yes/no) [yes]? [Enter] >>> Automatic Reboot <<<
Once scinstall has successfully installed and initialized the Sun Cluster software for this machine, it will be necessary to reboot. After the reboot, this machine will be established as the first node in the new cluster.
Do you want scinstall to reboot for you （yes/no) [yes]? yes You will need to manually reboot this node in \ scinstall successfully completes.
Hit ENTER to continue: [Enter] >>> Confirmation <<<
Your responses indicate the following options to scinstall: scinstall -ik \\ -C sc-igwb \\ -F \\
-T node=igwb1,node=igwb2,authtype=sys \\ -A trtype=dlpi,name=ce0 -A trtype=dlpi,name=ce5 \\ -B type=direct
Are these the options you want to use （yes/no) [yes]? [Enter] Do you want to continue with the install （yes/no) [yes]? [Enter]
8