end
RouterA#show running-config
Now create configuration... Current configuration !
hostname RouterA !
interface Ethernet0
ip address 202.101.10.1 255.255.255.0
ip ospf enable area 0.0.0.0 !
interface Serial0
encapsulation ppp !
interface Serial1
encapsulation ppp !
interface Serial2
flowcontrol normal
async mode dedicated
encapsulation ppp !
exit
router ospf enable ! end
RouterA#show ip route
Routing Tables:
Destination/Mask Proto Pref Metric Nexthop Interface
10.1.1.0/24 OSPF 10 20 202.101.10.2 Ethernet0 10.1.2.0/24 OSPF 10 20 202.101.10.2 Ethernet0
10.1.3.0/24 OSPF 10 20 202.101.10.2 Ethernet0
127.0.0.0/8 Static 0 0 127.0.0.1 LoopBack0 127.0.0.1/32 Direct 0 0 127.0.0.1 LoopBack0
202.101.10.0/24 Direct 0 0 202.101.10.1 Ethernet0
202.101.10.1/32 Direct 0 0 127.0.0.1 LoopBack0
7、在每台交换机和RouterA上配置enable password和line login password，观察他们能否相互Ping通，并试着从PC机和交换机上telnet到交换机或RouterA上。 -------------------------------------------------------------------------------- -- 作者：admin
-- 发布时间：2005-4-18 9:51:57 --
你可以将每台交换机的VLAN1接口配置如下：
SwitchA的VLAN1接口：202.101.10.2
SwitchB的VLAN1接口：202.101.10.3
SwitchC的VLAN1接口：202.101.10.4
SwitchD的VLAN1接口：202.101.10.5
SwitchE的VLAN1接口：202.101.10.6
以下是SwitchA的配置，其余交换机的配置也是类似的：
SwitchA#show running-config Building running configuration... Current configuration is : !
hostname SwitchA
enable password level 15 7 `C3CJaRZSBZa-,^U52H(_A!! user huawei password 0 huawei
spanning-tree enable
link-aggregation Ethernet0/1 to Ethernet0/2 ingress-egress
link-aggregation Ethernet0/9 to Ethernet0/10 ingress-egress
gvrp enable !
interface Aux0/0 !
vlan 1 !
vlan 2 !
vlan 3 !
vlan 4 !
interface Ethernet0/1
trunk all
gvrp enable !
interface Ethernet0/10
trunk all
gvrp enable !
interface Ethernet0/11
????
interface Ethernet0/2
trunk all
gvrp enable !
interface Ethernet0/20
????.
interface Ethernet0/9
trunk all
gvrp enable !
interface NULL0 !
interface VLAN-Interface1
ip address 202.101.10.2 255.255.255.0
!
interface VLAN-Interface2
ip address 10.1.1.100 255.255.255.0 !
interface VLAN-Interface3
ip address 10.1.2.100 255.255.255.0
interface VLAN-Interface4
ip address 10.1.3.100 255.255.255.0 router ospf
network 10.1.1.0 0.0.0.255 area 0.0.0.0
network 10.1.2.0 0.0.0.255 area 0.0.0.0
network 10.1.3.0 0.0.0.255 area 0.0.0.0
network 202.101.10.0 0.0.0.255 area 0.0.0.0 ! ! !
line aux 0
no login
line vty 0 4 login local ! end
SwitchE#telnet 202.101.10.2
Trying 202.101.10.2 ...
Connected to 202.101.10.2 ...
User Access Verification
Username:huawei Password:
SwitchA>enable Password: SwitchA#
8、试着在SwitchA上用端口e0/3监控e0/1，和端口e0/3的相连的PC机使用netXray或其它抓包软件来分析数据包，这样你就可以更清楚的观察发送的信息。