(2) Indicator lamp and warning lamp ① Direction indicator lamp
①.1 Left-turn signal lamp（No 1 in figure3-3-1）
Before turning left, pull the left switch group 2 back, the lamp will light up.
①.2 Right-turn signal lamp（No 8 in figure 3-3-1）
Before turning right, push the left switch group 2 forward, the lamp will light up.
② Fog lamp
①.1 Front fog lamp (No 1 in figure 3-3-2)
This lamp indicates when the front fog lamp is applied.
①.2 Rear fog lamp (No 2 in figure 3-3-1)
This lamp indicates when the rear fog lamp is applied.
③ Parking brake warning lamp（No 3 in figure 3-3-1）travelling.
This lamp indicates when the parking brake is applied. Please make sure that this lamp is off before
④ Engine hydraulic pressure warning lamp（No 4 in figure 3-3-1)）immediately stop the vehicle and turn off the engine.
If this warning lamp lights up, it indicates that the oil pressure is less than the normal pressure,
⑤ Low battery warning lamp（No 5 in figure 3-3-1）
This lamp indicates when the battery voltage is low; please charge as soon as possible.
⑥ Front axle air pressure warning lamp（No 6 in figure 3-3-1）
This lamp indicates when the air pressure in the braking circuit of front axle is too low.
⑦ Auxiliary air pressure warning lamp（No 7 in figure 3-3-1）
This lamp indicates when the air pressure in the auxiliary air circuit is too low.
⑧ Engine brake indicator lamp（No 9 in figure 3-3-1）
7
This lamp indicates when the engine braking is applied.
⑨ Low fuel warning lamp（No 10 in figure 3-3-1）
This warning lamp lights up when the fuel is not sufficient, please add the fuel in time.
Cautions: Drivers should always check the fuel gauge and add fuel timely. If warning lamp lights up,
add the fuel in time.
⑩ Warning lamp for engine coolant temperature（No 11 in figure 3-3-1）
This lamp indicates when the coolant temperature of the engine is too high.
? High beam lamp（No 12 in figure 3-3-1）
This lamp indicates when the high beam lamp switch is pressed down.
? Warning lamp for middle and rear axle air pressure（No 13 in figure 3-3-1）
This lamp indicates when the brake circuit air pressure of the middle and rear axles are too low.
? Parking brake air pressure warning lamp（No 14 in figure 3-3-1）
This lamp indicates when the parking brake circuit air pressure is too low. Never relieve the parking brake before this lamp is off. ? Engine warning lamp
①.1 Engine fatal failure warning lamp（Red）（No 2 in figure 3-3-2）
If vehicle occurs have problems, “failure” red lamp lights up, it means the engine maybe safe shut-down, in order to reduce the possibilities to damage the engine, the driver must pull over and stop the vehicle at once. The engine will not be started unless problems were solved.
①.2 Engine general failure warning lamp（Yellow）（No 3 in figure 3-3-2）
If “warning” lamp (yellow) lights up, it may need to solve the problem at once.
? Top gear indicator lamp（No 4 in figure 3-3-2）
This lamp indicates when the top gear is working.
? Low gear indicator lamp（No 5 in figure 3-3-2）
This lamp indicates when the low gear is applied.
8
? Turn signal indicator lamp in emergency（No 6 in figure 3-3-2）
1) Switch on the main power, insert and turn the key-indicator lamp on (it indicates that the emergency steering system is able to work)
2) Start the engine, then the vehicle is in idle speed-indicator lamp on (normal) 3) Drive the vehicle, once the speed is over 10 km/h,-indicator lamp out (normal)
4) If the general steering system is fault when traveling (such as fault occurs in steering pump and engine is stopped), emergency steering system is applied-indicator lamp on (normal, it indicates that the emergency steering system is working)
The four principles are the working status of emergency steering system; others are considered the parts fault or problems from the manufacturer.
? Engine standby lamp（Green）（No 7 in figure 3-3-2）
The engine does not start when it is too cold. Standby lamp lights up when it need to waiting.
? Low beam lamp（No 8 in figure 3-3-2）
This lamp indicates when the switch of the low beam lamp is pressed down.
? Air cleaner warning lamp（No 9 in figure 3-3-2）(3) Switches and controls
When the air cleaner filter is clogged, this lamp will light up, please clean or replace the air filter. ① Starter switch
Starter switch is placed into the steering column(No 4 in figure 3-1)。Depress down the clutch and turn the key when starting the engine. Position key into starter switch, there are four optional positions, please refer to figure 3-4。
The functions of them are as follows:
LOCK: The key can be inserted and removed in this position.
ACC: Accessories such as radio and cigar lighter could be used when the key is turned to“ACC”, even the engine is stopped.
Figure 3-4 Starter switch ON: While the engine is running, the key is in this position.
START: Turn the key to this position and hold on for a moment, release the key after the engine is started. Then the key returns to “ON” automatically.
Cautions: Keep the key in the position of “ON” while the engine is running,
Warnings: Never turn the key to the position of “LOCK”, or else the steering wheel will be locked, it
will make the vehicle out of control and resulting in severe personal injury or vehicle
damage.
② Switch group 2
Switch group is composed of steering switches, lighting switches, wiper switches and engine braking switches.
9
Figure 3-5 Switch group 2
②.1 How to use steering switches:
Before turning left, pull the left switch group back, and the left-turn signal lamp flashes（No 1 in figure 3-3-1）. Before turning right, push the switch group forward, and the right-turn signal lamp flashes（No 8 in figure 3-3-1）. And at the same time, the corresponding indicator lamp on the instrument panel begins to flash. For lane changing, operate the switch in accordance with the operation-method of steering signal lamp. ②.2 How to use lighting switches:
②.2.1 High beam and Low beam lamp
Switch the combination switch handle on the left side to make the small arrow alignment level to and the position lamp starts to work. Switch the combination handle on the left side to make the small arrow alignment level to , high beam indicator lamp indicates and high beam lamp is working.（No 12 in figure 3-3-1）.When connected, the handle is in a low beam position (middle position).Lift up combination switch handle from the middle position, high beam position can be reached. Another lift will reach low beam position, the low beam lamp starts to work and low beam indicator lamp on（No 8 in figure 3-3-2）.
Switch the combination switch handle on the left side to make the small arrow alignment level to OFF. Lift up and hold the handle and high beam lamp is still lightening, release the handle, and the lamp goes off.
②.2.2 Emergency signal switch (dual-lamp flashing)
Emergency signal switch appears as red on the combination switch on the right side. Lift up the combination switch handle and emergency signal lamp starts to work, another lift will shut down the lamp.
If the vehicle has to be placed in a place that is dangerous, emergency signal lamp must be applied. (light the turn signals to demonstrate the emergency).When the emergency signal switch is connected, all the turn signal lamps begin to flash, and the hazard warning lamp is still flashing even if the key is on the “lock” position. Turn off the hazard lamp switch, and the warning was released.
10
②.3 How to use wiper
Switch right handle of the combination switch to control the wiper, rotate the handle to make the small arrow alignment level to HI ,and the wiper is in high-speed working status, rotate the handle to make the small arrow alignment level to LO ,and the wiper is in low-speed wording status, switch the combination switch handle on the right to make the small arrow alignment level to INT ,and the wiper is in intermittent working status, rotate the handle to make the small arrow alignment level to OFF ,and ，and the washer starts to work. the wiper is turned off. Press the button②.4 Engine brake switch
Engine brake switch is on the right side of the combination switch handle. When the lever is pulled
backward, the engine brake starts to work; pull forward the lever, the engine brake released.
Before using the engine brake, please make sure that the engine speed is over 1020rpm, and put foot off the accelerator pedal, the clutch is engaged, or else the engine braking is unable to work. CAUTIOUS: when the engine braking is applied:
﹡The engine speed in 1600-2200rpm is more efficient for engine braking. When the engine speed is less than 980rpm, the engine braking is disabled. Never keep the engine speed more than 2300 rpm.
﹡If the vehicle is on ramp with load, and driver drive the vehicle more faster than the steady speed. The engine braking can be used at high gears while brake pedal is depressed down interruptedly to protect the engine from over speed and keep the vehicle in a safety speed. If the driver prefers slower speed than steady speed when traveling on the ramp, a lower gear and foot brake are required, all that are considered to keep lower speed and con troll engine speed.
﹡Injector will not work when the engine brake is applied, economic engine speed need not be considered.
﹡Never apply engine braking on the road covered with ice or snow, apply it cautious on wet road.
③ Horn switch
Horn switch(No 9 in figure 3-1) is on the steering wheel，air horn switch is on the instrument panel(No 1 in figure 3-3-3), press down the switch ,the horn blares.
④ Fog lamp switch
One of the fog lamps is on the instrument panel(No 2 in figure 3-3-3)，and the other one is in front of steering column, and they are represented by a symbol of . The switch of rear fog lamp is in the instrument panel, the switch of front fog lamp is in the steering column.
When this switch is connected, the fog lamps and indicators are light on.
⑤ PTO switch (No 3 in figure 3-3-3)
Behind the transmission is the PTO which drives hydraulic pump to operate the auto crane.
Operating instructions: Stop the vehicle and run the engine at idle speed, put the gearshift lever in the
11