微通道论文(4)

2019-04-14 14:27

7.2 monolith 型

Monolith 型材料是一种由 Al-Si-Mg 氧化物等按照一定的比率组成的具有规则通道的陶瓷材料,具有耐高温,化学稳定性好等优点,可以在一定程度上避免金属材料对催化层的影响。

对于采用 monolith 型催化剂进行SRE反应研究方面,Llorca J. 及其合作者开展了广泛而深入的工作[60,64-66],该组采用Co基催化剂以低温SRE反应

(200~500 ℃)在微反中进行乙醇重整制氢研究\对催化层的沉积方法,通道直径等影响因素做了考察。结果表明,通过合适的催化层沉积方法(如尿素分解沉积,气凝胶沉积等)可以有效的提高催化剂活性组分如Co的分散度,从而提高反应的活性[65-66]

。Llorca J. et al采用光辅助电化学蚀刻法制备了直径约7 mm的微型硅基monolith,其中,微通道的尺寸为 3.3 Lm@210 Lm,通道的数目达到1.5@106\使用此种材料进行了 SRE 反应的研究,并与 400 PPI 的monolith 型以及金属微通道型(78 mm@700 Lm@350 Lm)的催化剂进行了比较,结果表明在monolith 和金属微通道型反应器中,乙醇具有较高的转化率,但在相近条件下(如 T = 400 ~

500 ℃,EtOH:H2O = 6,乙醇转化率 30~42 %等),硅基微反中体积效率最高(>52000 mLH2/(mLfeed, l )) 。Si-Al 型 monolith 是非金属材料,具有较低的热传导系数,是良好的保温材料,由于 SRE 是强吸热反应,需要外界供热。非金属的 monolith 不利于热传导,所得的催化剂容易在反应时出现温度梯度,造成中心温度偏低,可能会引起催化剂积炭等使得性能下降,当催化剂的体积较大时,这种作用尤为明显\因此,当它用于 SRE 反应时,只适合制成体积/直径较小的(如直径<1 cm)催化剂,输出的产品气的产量也受到限制。

八 微反应器的制作材料和技术

制造微反应器使用的材料比较广泛, 如金属、聚合物、陶瓷、玻璃和硅等。金属设备适用于快速放热多相催化反应, 玻璃和硅制成的微反应器适合于多种化学反应, 如药物快速筛选和多相催化反应。

制作微反应器的微加工技术种类繁多, 因微反应器的性能和材料而异。通常微反应器的制作需综合运用多种微加工技术, 如脱氢/ 加氢微膜反应器的制作就应用了低压化学气相沉积法和湿法氧化刻蚀等多种技术。目前用于制作微反应器的微加工技术主要有: 单晶材料的整体微加工技术, 低压等离子体或离子束干式刻蚀法, 光刻、电铸和塑模结合的工艺(L IGA 工艺,微模塑技术, 玻璃的湿式化学刻蚀, 铣、削、锯、模压、冲孔和钻孔等精加工技术,金属薄片的各向同性湿式化学刻蚀, 微电火加工技术(μEDM)和激光烧蚀技术等。

九 展望

最近几年来, 国外学术界对微反应器进行了深入的研究, 对微反应器的原理和应用有了比较透彻的认识, 在微反应器的设计、制造、集成和放大等关键问题上已经取得了突破性进展。尤其是在微反应器的设计和制造上, 达到了相当高的水平, 已经用适当的工艺和材料制造出了微反应泵、微混合器、微反应室、微换热器、微分离器和具有控制单元的完全耦合微反应系统。但微反应器要取代传统反应器应用于实际生产,还需要解决一系列难题, 如微通道易堵塞、催化剂设计、传感器和控制器的集成及微反应器的放大等。微反应器的放大看起来简单, 但要实现却是一个巨大的挑战。当微反应器的数量大大增加时, 微反应器监测和控制的复杂程度大大增加了。展望未来微反应器研究, 预计将在以下几个领域取得进展:

(1) 设计新的微反应器模型, 对微反应器进行耦合、集成和“放大”。 (2) 在微反应器中研究反应原理, 对微反应器的设计进行模拟、优化。

(3) 在微反应器中探索新的反应途径和使化工生产更加经济更加环保的方法, 并应用于实际

生产, 这是研究微反应器的真正价值所在。

参考文献

[1 ] Hessel V , Lêwe H , Stange T. Micro chemical processing at IMM-from pioneering work to customer specific services[J ] . Lab Chip , 2002 , 2 (1) : 14 - 21. [2 ] Jensen K F. Microreaction engineering —is small better ?[J ] . Chem Eng Sci , 2001 , 56 (2) : 293 - 303.

[3 ] Jahnisch K, Hessel V , Lêwe H , et al. Chemistry in microstructured reactors [J ] . Angew Chem Int Ed , 2004 ,43 (4) : 406 - 446.

[4 ] Wagner J , Kêhler J M. Continuous synthesis of gold nanoparticles in a microreactor [J ] . Nano Lett , 2005 , 5 (4) : 685 - 691.

[5 ] Nie Z H , Xu S Q , Seo M , et al. Polymer particles with various shapes and morphologies produced in continuous microfludic reactors [ J ] . J Am Chem Soc , 2005 , 127(22) : 8058 - 8063.

[6 ] Song Y J , Doomes E E , Prindle J , et al. Investigation into

sulfobetaine-stabilized Cu nanoparticles formation :Toward development of a microfluidic synthesis [ J ] . J Phys Chem B , 2005 , 109 (19) : 9330 - 9338. [7] Schubert K. [J ] . Chem. Ing. Tech. , 1998 ,27 (10) :124~127

[8] Ehfreld W, Hessel V ,Lêwe H. Microreactors :New Technology for Modern Chemistry[M] . Weinheim: Willy - VCH ,2000

[ 9] Woolley A T ,Mathies R A. [J ] . Proc. Natl . Acad. Sci . , 1994 ,91 :11348~11352

[10] Manz A , Effenhauser C S , Barggraf N , et al. [J ] . A nal . Mag. ,1994 ,22 :M25

[11] Lerous J J , Harold M P , Ryley J , et al. Microfabricated Minichemical

Systems : Technical Feasibility. In : Ehrfeld W MicrosystemTechnol. for Chem. and Biol. Microreactors. Weinheim: Verlag Chemie ,1996 ,51~69

[12] Ehrfeld W, Hessel V , Mo K H ,et al. Potential and Realization of Microreactors. In : Ehrfeld W. Microsystem Technol. for Chem.and Biol. Microreactors. Weinheim: Verlag Chemie ,1996 ,1~28.

[13] Weber L. [ J ] . Nachr. Chem. Tech. L ab. , 1994 , 42 ( 7 ) :698~702 [14] Balkenhohl F , von dem Bussche - Hünnefeld C , Lansky A , et al.[J ] . A ngew . Chem. , 1996 ,108 :2437~2488

[15] J ung G, Bech - Sichinger A G. [ J ] . A ngew . Chem. , 1992 , 104 :375~500 [16] Wolfgang Ehrfeld V. H., Holger L?we, Microreactors: new technology for modern chemistry, Mainz: WILEY-VCH, 2000

[17] Shao N., Gavriilidis A., Angeli P., Flow regimes for adiabatic gas- liquid flow in microchannels, Chemical Engineering Science, 2009, 64 (11): 2749~2761 [18] Bretherton F. P., The motion of long bubbles in tubes, Journal of Fluid Mechanics,1961, 10: 166~188

[19] SuoO M., Griffith P., Two-phase flow in capillary tubes, J. Basic Eng, 1964, 86:576~582

[20] Thayer A. M., Harnessing microreactions, Chemical & Engineering News,

2005,83(22): 43~49

[21] Watts P., Haswell S. J., The application of microreactors for small scale organic synthesis, Chemical Engineering & Technology, 2005, 28(3): 290~301 [22] Borovinskaya E. S., Reshetilovskii V. P., Microstructural reactors:

concept,development and application, Russian Journal of Applied Chemistry, 2008, 81(12):2211~2231

[23] Kandlikar S. G., Fundamental issues related to flow boiling in minichannels and microchannels, Experimental Thermal and Fluid Science, 2002, 26(2~4): 389~407

[24] Kandlikar S. G., Flow boiling heat transfer coefficient in minichanne ls-correlation and trends, The proceedings of the International Heat Transfer Conference, 2002

[25] Rebrov E V , de Croon M H J M , Schouten J C. [ J ] . Catal .Today , 2001 ,69 :183~192

[26] Srinivasan R , Hsing I M , Berger P E , et al. [ J ] . A IChE J . ,1997 ,43 : 3059~3069

[27] Franz A , Jensen K F , Schmidt M A. Palladium Based Micromembranes for Hydrogen Separation and Hydrogenation/ Dehydrogenation Reactions. In : Ehrfeld W. Microreaction Technology : Industrial Prospects. Berlin : Springer ,2000 ,267~276 [28] W?rz O , J?c kel K P , Richter Th , et al. [J ] . Chem . Eng. Sci . ,2001 ,56 :1029~1033 [29] W?rz O ,J?ckel K P. [J ]. Chem. Techn. ,1997 ,131 (26) :130 ~134 [30] Floyd T M , Losey M W, Firebaugh S L , et al. Novel Liquid Phase

Microreactors for Safe Production of Hazardous Specialty Chemicals . In : Ehrfeld W. Microreaction Technology : Industrial Prospects. Berlin :Springer ,2000 ,171~180 [31] Daykin R N C , Haswell S J . [J ] . A nal . , Chim. Acta. , 1995 ,313 (3) :155~159

[32] Haverkamp V , Emig G, Hessel V , et al. Characterization of a Gas/Liquid Microreactor , the Microbubble Column : Determination of Specific Interfacial Area[C] . Proc. of the 5th Int . Conf . onMicroreaction Technology , IMERT 4 , Strasbourg , France , 2001

[33] Losey M W, Schmidt M A , Jensen K F. A Micro Packed - bed Reactor for Chemical Synthesis. In : Ehrfeld W. Microreaction Technology : Industrial Prospects. Berlin : Springer ,2000 ,277~286

[34] Losey M W, Schmidt M A , Jensen K F. [J ] . Microengineering ,2000 ,6 :285~289 [35] J?h nisch K, Baerns M , Hessel V , et al. [J ] . J . Fluorine Chem. ,2000 ,105 (1) :117~128 [36] L?we H , Ehrfeld W, Küpper M , et al. Electrochemical Microreator : A New Approach in Microreaction Technology[ C] . 3rd Int .Conf . on Microreaction Technology , Proc. of IMERT 3 , Berlin ,2000

[37] Lu H , Schmidt M A , Jensen K F. Photochemical Reactions and on - line Monitoring in Microfabricated Reactors[ C] . Proc. of the 5th Int . Conf . on Microreaction Technology , IMERT 4 , Strasbourg , France , 2001

[38] Lu H , Schmidt M A , Jensen K F. [J ] . L ab on a Chip. , 2001 ,1 :22~28 [39] Pfahler J., Harley J., Bau H., Zemel J., Liquid transport in micron and submicron channels, Sens. Actuators A, 1990, 21: 43l~434

[40] Peng X. F., Peterson G. P., Wang B. X., Frictional flow characteristics of water flowing through rectangular microchannels, Exp. Heat Transfer, 1994,7:249~264

[41] Murshed S.,Tan S., Nguyen N., et.al., Microdroplet formation of water and nanofluids inheat-induced microfluidic T-junction. Microfluidics and Nanofluidics, 2009, 6(2): 253~259

[42] Zhao Y., Su Y., Chen G., et.al., Effects of surface properties on the flow characteristics and mass transfer performance in microchannels. Chemical Engineering Science, 2010, 65(5): 1563~1570

[43] Burns J.R., Ramshaw C., A microreactor for the nitration of benzene and toluene.Chemical Engineering Communications, 2002, 189(12): 1611~1628 [44] Bums J. R., Ramshaw C., Development of a microreactor for chemical production,Chem. Eng. Res., 1999, 77 (A3):206~211

[45] Manabu T., Tomoko M., Integration of a microextraction system: Solvent extraction of a Co-2-nitroso-5-dimethylaminophenol complex on a microchip,Journal of Chromatography A, 2000, 894: 19~23

[46] 王安琦,王洁欣,余文等,微通道反应器微观混合效率的实验研究,北京化工大学学报(自然科学版),2009, 36(3): 1~5

[47] Gobby D, Angeli P G., Mixing characteristics of T-type Microfluidic mixers,Journal of Micromechanics and Microengineering, 2001, 11: 126~132 [48] Mengeaud V., Josserand J., Girault H. H., Mixing processes in a zigzag mierochannel: finite element simulations and optical study, Anal. Chem., 2002,74: 4279~4286

[49] Yue J., Chen G. W., Yuan Q., Hydrodynamics and mass transfer

characteristics in gas-liquidflow through a rectangular microchannel, Chemical Engineering Science, 2007, 62 (7): 2096~2108

[50] Marcandelli C., Lamine A. S., Bernard J. R., Liquid distribution intrickle-bed reactor, Oil and Gas Science and Technology, 2000, 55(Compendex): 407~415 [51] Roy S., Al-Dahhan M., Flow distribution characteristics of a gas-liquid monolith reactor, Catalysis Today, 2005, 105(3~4): 396~400

[52] Bauer T., Roy S., Lange R., Liquid saturation and gas-liquid distribution in multiphase monolithic reactors, Chemical Engineering Science, 2005, 60(11):3101~3106

[53] Wu H. Y., Cheng P., Visualization and measurements of periodic boiling in silicon microchannels, International Journal of Heat and Mass Transfer, 2003, 46(14):2603~2614

[54] Tan J., Liu Z.D., Lu Y.C., et. al., Process intensi?cation of H2O2 extraction using gas-liquid-liquid microdispersion system, Separation and Puri?cation Technology, 2011, 80, 225~234

[55] Meille V. Review on methods to deposit catalysts structured surfaces [J ] . Applied Catalysis A2General ,2006 ,315 :1 - 17.

[56] Kanno K,Fujii M. Microreactor :New device for organic and enzymatic synthesis [J ] .Journal of Synthetic Organic Chemistry Japan Synthetic ,2002 ,60 (7) :701 - 707.

[57] Ehrfeld W. J., Hessel V., Haverkamp V., Microreactors, Ullmann\Encyclopedia of Industrial Chemistry, Wiley-VCH, Weinheim, 1999

[58] Lerou J. J., Harold M. P., Ryley J., Microfabricated mini-chemical

systems:technical feasibility, in Ehrfeld Microsystem Technology for Chemical and Biological Microreactors, Verlag Chemic, Weinheim, 1996, (32): 51~69

[59] Gorke O., Pfeifer P., Schubert K. Kinetic study of ethanol reforming in a microreactor[J]. Applied Catalysis a-General, 2009, 360(2): 232-241

[60] Llorca J., Casanovas A., Trifonov T., et al. First use of macroporous silicon loaded with catalyst film for a chemical reaction: A microreformer for producing hydrogen from ethanol steam reforming[J]. Journal of Catalysis, 2008, 255(2): 228-233

[61] Wanat E. C., Venkataraman K., Schmidt L. D. Steam reforming and water-gas shift of ethanol on Rh and Rh-Ce catalysts in a catalytic wall reactor[J]. Applied Catalysis a-General, 2004, 276(1-2): 155-162

[62] Casanovas A., Saint-Gerons M., Griffon F., et al. Autothermal generation of hydrogen from ethanol in a microreactor[J]. International Journal of Hydrogen Energy, 2008, 33(7): 1827-1833

[63] Tadd A. R., Gould B. D., Schwank J. W. Packed bed versus microreactor performance in autothermal reforming of isooctane[J]. Catalysis Today, 2005, 110(1-2): 68-75

[64] Dominguez M., Taboada E., Molins E., et al. Co-SiO2 aerogel-coated catalytic walls for the generation of hydrogen[J]. Catalysis Today, 2008, 138(3-4): 193-197 [65] Casanovas A., Dominguez M., Ledesma C., et al. Catalytic walls and micro-devices for generating hydrogen by low temperature steam reforming of ethanol[J]. Catalysis Today, 2009, 143(1-2): 32-37

[66] Casanovas A., de Leitenburg C., Trovarelli A., et al. Catalytic monoliths for ethanol steam reforming[J]. Catalysis Today, 2008, 138(3-4): 187-192


微通道论文(4).doc 将本文的Word文档下载到电脑 下载失败或者文档不完整,请联系客服人员解决!

下一篇:人教版八年级生物上册期末考试复习提纲 绝对押题

相关阅读
本类排行
× 注册会员免费下载(下载后可以自由复制和排版)

马上注册会员

注:下载文档有可能“只有目录或者内容不全”等情况,请下载之前注意辨别,如果您已付费且无法下载或内容有问题,请联系我们协助你处理。
微信: QQ: