AMI Turbitrack
Trouble Shooting
Error E033
Description Power-on Power-down 光度计玷污 过滤器堵塞，更换。
E034
E065
E066
}
正常状态
8.3 Messages信息
如果屏幕上有 ! 符号出现，必需对仪表进行维护。
36 A-96.250.441 / 060923
AMI Turbitrack
Appendix
A.
附录
A.1 程序概述
Pending Errors
Messages (Main Menu 1)
Maintenance List Message List
1.1* 1.2* 1.3*
Identification
Factory Test
Instrument Motherboard Front End Years Days Hours :
Photometer Raw Value 1 Raw Value 2 Cal. History Ver. History
2.1.4.1* Designation AMI TURBI Version 2.20-01/05 Version TURBI
2.1.5.1* Operating Time
Photometer
Sensor
Diagnostics (Main Menu 2) Turbi
Miscellaneous Case Temp.
Quotient V-Signal V-Ref 2.3.1* 2.2.1.4* 2.2.1.5* 2.2.2.1* 2.2.3.1*
Sample
Sample ID Sample Flow (Raw value)
I/O State
Alarm Relay Relay 1/2
Input
Signal Output 1/2
2.4.1*
Interface
Protocol Baud rate
A-96.250.441 / 060923 37
AMI Turbitrack
Appendix
Verification Cleaning
3.1*
Manual operation
3.2.1*
Automatic
Maintenance(Main Menu 3)ModeRun TimeStart Time
3.2.2.1*3.2.2.2*3.2.2.3*
Simulation
Set Time Alarm Relay Relay 1/2Signal Output 1/2
3.3.1*
3.4*
Filter Time Const.
Sensors
Hold after Cal.
4.1.1* 4.1.2* Range Low
Range High Range HighRange Low4.2.1.100* 4.2.1.200* 4.2.2.101*4.2.2.201*
Signal Outputs
Signal Output 1
Signal Output 2
Operation
(Main Menu 4)
Alarm Relay
Relay Contacts
Relay 1/2 Input
Alarm FNU }
see p. 39
Logger
Log IntervalClear Logger
4.4.1*4.4.2*
38 A-96.250.441 / 060923
AMI Turbitrack
Appendix
Sensor Type
Track
5.1.1*
Sensors
Temperature none Flow
Q-Flow
OffsetRange GainScale Factor 1Scale Factor 2
Signal Outputs
Factory Parameters
Signal Output 1/2
5.1.4.1*5.1.4.2*5.1.4.3*5.1.4.4*
Parameter Current Loop Function
Scaling (depends on Function)
Installation (Main Menu 5)
Relay Contacts
Alarm Relay Alarm FNUSampleCase Temp. highCase Temp. low
5.3.1.1*5.3.1.2*5.3.1.3*5.3.1.4*
Relay 1/2
Function Parameter
Limit/settings (dep. on Function)
Input Active 5.3.4.1*
Miscellaneous LanguageSet defaultsLoad FirmwarePasswordSample ID
5.4.1*5.4.2*5.4.3*5.4.4*5.4.5*
Interface
Protocol Baud Rate
A-96.250.441 / 060923 39
AMI Turbitrack
Appendix
A.2 消费者备件及替换件列表
将所收到的货物与订货单相对照。
Order scheme Monitor AMI Turbitrack Power supply:
85-265 VAC / 47-63 Hz
A-25.41 . 2
24 VDC, direct current
? 1
2 0 ??
Interface option:
None
Profibus DP communi- cation interface
0
2
A.3 解释
延迟
0-600 sec, 缺省 30 sec 信号延迟时间。
过滤时间常数
5-300 sec, 缺省30 sec 用于消除干扰信号。
过滤常数越大，系统对测量值变化作出反应越迟缓。
校准后维持时
间
5-6000 sec, 缺省30 sec
校准期间，信号输出和报警继电器重新激活，校准后维持的这段时间可以适当延长直到测量到稳定值。
迟滞
主要防止因继电器开和关设置为同一数值时而咔嗒作响。 大约设置为限位的10%。
40 A-96.250.441 / 060923