ISCREATE Created by 许达敏 32101880.doc Created on 11/23/2000 9:59:00 PM Page 6 of 38 ALEXI:DEV=EXAL0-46;
ALRDL:DEV=EXAL0-47,CAW1=\ ALEXL:DEV=EXAL0-47,ACL=A2,ALCAT=12; ALEXI:DEV=EXAL0-47;
! ACU ALARMS CELL C!
ALRDL:DEV=EXAL0-40,CAW1=\ ALEXL:DEV=EXAL0-40,ACL=A1,ALCAT=12; ALEXI:DEV=EXAL0-40;
ALRDL:DEV=EXAL0-41,CAW1=\ ALEXL:DEV=EXAL0-41,ACL=A1,ALCAT=12; ALEXI:DEV=EXAL0-41;
ALRDL:DEV=EXAL0-42,CAW1=\ ALEXL:DEV=EXAL0-42,ACL=A2,ALCAT=12; ALEXI:DEV=EXAL0-42;
ALRDL:DEV=EXAL0-43,CAW1=\ ALEXL:DEV=EXAL0-43,ACL=A2,ALCAT=12; ALEXI:DEV=EXAL0-43;
! 230 VAC POWER SUPPLY ! ! 230 VAC POWER SUPPLY is an alternative ! ! to -48 VDC POWER SUPPLY !
! ALRDL:DEV=EXAL0-24,CAW1=\BTS\ ! ALEXL:DEV=EXAL0-24,ACL=A1,ALCAT=12; ! ! ALEXI:DEV=EXAL0-24; !
! ALRDL:DEV=EXAL0-25,CAW1=\BTS\ ! ALEXL:DEV=EXAL0-25,ACL=A2,ALCAT=12; ! ! ALEXI:DEV=EXAL0-25; !
! ALRDL:DEV=EXAL0-26,CAW1=\BTS\ ! ALEXL:DEV=EXAL0-26,ACL=O1,ALCAT=12; ! ! ALEXI:DEV=EXAL0-26;
! ALRDL:DEV=EXAL0-27,CAW1=\failure\ ! ALEXL:DEV=EXAL0-27,ACL=A1,ALCAT=12; ! ! ALEXI:DEV=EXAL0-27; !
! ALRDL:DEV=EXAL0-28,CAW1=\voltage\
ISCREATE Created by 许达敏 32101880.doc Created on 11/23/2000 9:59:00 PM Page 7 of 38 ! ALEXL:DEV=EXAL0-28,ACL=A2,ALCAT=12; ! ! ALEXI:DEV=EXAL0-28;
! -48 VDC POWER SUPPLY CELL A!
!85000,1! !Cell Data!
!-------------------------------------------------------------------------! ! ***** INTERNAL CELL NAME ***** ! !-------------------------------------------------------------------------! RLDEI:CELL=Z12XTG1,CSYSTYPE=GSM; RLDEI:CELL=Z12XTG2,CSYSTYPE=GSM; RLDEI:CELL=Z12XTG3,CSYSTYPE=GSM;
定义小区及小区类型（千万不要随便用RLDEE：CELL=XXXXXXX；否则小区数据会全部丢失，不过RLDEE也不是随便就能成功）
!-------------------------------------------------------------------------! ! ***** INTERNAL CELL DESCRIPTION DATA ***** ! !-------------------------------------------------------------------------!
RLDEC:CELL=Z12XTG1, CGI=460-00-9508-2671,BSIC=63,BCCHNO=84, AGBLK=1, MFRMS=2, BCCHTYPE=NCOMB, FNOFFSET=0, XRANGE=NO; RLDEC:CELL=Z12XTG2, CGI=460-00-9508-2672,BSIC=63, BCCHNO=53, AGBLK=1, MFRMS=2, BCCHTYPE=NCOMB, FNOFFSET=0, XRANGE=NO; RLDEC:CELL=Z12XTG3, CGI=460-00-9508-2673, BSIC=63, BCCHNO=88 , AGBLK=1, MFRMS=2, BCCHTYPE=NCOMB, FNOFFSET=0, XRANGE=NO; BCCH要在这里定义，DCH则在RLCFI里定义，注意这里的CGI要和MSC里的一致。 改变小区的BCCH也是用RLDEC：CELL=XXXXXXX，BCCH=XX；如果这里的BCCH和交换机里的相同，会定义不进去（CGI则可以）。
!-------------------------------------------------------------------------! ! ***** CONNECT A CHANNEL ALLOCATION PROFILE CELL(S) ***** ! !-------------------------------------------------------------------------!
RLHPC:CELL=Z12XTG1, CHAP=0; !### RLHPC:CELL=Z12XTG2, CHAP=0; !### RLHPC:CELL=Z12XTG3, CHAP=0; !###
!-------------------------------------------------------------------------! ! ***** DEFINITION OF SUBCELL ***** ! !-------------------------------------------------------------------------!
!RLDSI:CELL=Z12XTG1; NO SUBCELL ! !RLDSI:CELL=Z12XTG2; NO SUBCELL !
ISCREATE Created by 许达敏 32101880.doc Created on 11/23/2000 9:59:00 PM Page 8 of 38 !RLDSI:CELL=Z12XTG3; NO SUBCELL !
!-------------------------------------------------------------------------! ! ***** CHANGE OF TRAINING SEQUENCE CODE ***** ! !-------------------------------------------------------------------------!
! RLDTC:CELL=Z12XTG1,SCTYPE=sctype, TSC=tsc; NO SUBCELL ! ! RLDTC:CELL=Z12XTG2,SCTYPE=sctype, TSC=tsc; NO SUBCELL ! ! RLDTC:CELL=Z12XTG3,SCTYPE=sctype, TSC=tsc; NO SUBCELL !
!-------------------------------------------------------------------------! ! ***** CHANNEL GROUP DATA ***** ! !-------------------------------------------------------------------------!
! RLDGI:CELL=Z12XTG1, CHGR = 0, SCTYPE=UL; CHGR=0 DEFINED BY RLDEI ! ! RLDGI:CELL=Z12XTG2, CHGR = 0, SCTYPE=UL; CHGR=0 DEFINED BY RLDEI ! ! RLDGI:CELL=Z12XTG3, CHGR = 0, SCTYPE=UL; CHGR=0 DEFINED BY RLDEI !
!-------------------------------------------------------------------------! ! ***** CONFIGURATION FREQUENCY DATA ***** ! !-------------------------------------------------------------------------!
RLCFI:CELL=Z12XTG1, CHGR=0, DCHNO=72&60&48&36&24; RLCFI:CELL=Z12XTG2, CHGR=0, DCHNO=41&77&89&31&27&95; RLCFI:CELL=Z12XTG3, CHGR=0, DCHNO= 28&40&52&64&76;
这里定义的是DCH，BCCH要在前面的RLDEC里定义。如果想改频点，最好先把新的频点定义进去，然后才把多余的频点删掉。如果只是要删去频点，可以用RXCDP：MO=RXOTG-XX（RXETG-XX）；来看哪个频点没有被占用，如果要删的频点是有SDCCH的，最好用RLCCC把SDCCH=0，然后就可以把频点删除，记住要把SDCCH改回去）
!-------------------------------------------------------------------------! ! ***** CONFIGURATION CONTROL CHANNEL ***** ! !-------------------------------------------------------------------------! RLCCC:CELL=Z12XTG1, CHGR=0, SDCCH=3, CBCH=NO, TN=2, CCHPOS=TN; RLCCC:CELL=Z12XTG2, CHGR=0, SDCCH=3, CBCH=NO, TN=2, CCHPOS=TN; RLCCC:CELL=Z12XTG3, CHGR=0, SDCCH=3, CBCH=NO, TN=2, CCHPOS=TN; SDCCH数目的确定：（TCH数目+1）/2
!-------------------------------------------------------------------------! ! ***** CONFIGURATION FREQUENCY HOPPING ***** ! !-------------------------------------------------------------------------! RLCHC:CELL=Z12XTG1, CHGR=0, HOP=ON, HSN=45; RLCHC:CELL=Z12XTG2, CHGR=0, HOP=ON, HSN=41; RLCHC:CELL=Z12XTG3, CHGR=0, HOP=ON, HSN=44;
ISCREATE Created by 许达敏 32101880.doc Created on 11/23/2000 9:59:00 PM Page 9 of 38 HSN在一个基站里不要相同
!-------------------------------------------------------------------------! ! ***** CONFIGURATION POWER DATA ***** ! !-------------------------------------------------------------------------!
RLCPC:CELL=Z12XTG1, BSPWRB=45, BSPWRT=45, MSTXPWR=33; RLCPC:CELL=Z12XTG2, BSPWRB=45, BSPWRT=45, MSTXPWR=33; RLCPC:CELL=Z12XTG3, BSPWRB=45, BSPWRT=45, MSTXPWR=33;
注意2000站有些TRU的功率是达不到47的，对于1800功率有不同的要求，会比900的要小，MSTXPWR是等于30的。但是如果基站功率设置得太小，有些载波会开不起来。
!-------------------------------------------------------------------------! ! ***** CONFIGURATION DTX DOWNLINK ***** ! !-------------------------------------------------------------------------! RLCXC:CELL=Z12XTG1, DTXD=ON; RLCXC:CELL=Z12XTG2, DTXD=ON; RLCXC:CELL=Z12XTG3, DTXD=ON;
没有特别情况最好把DTXD（下行不连续发射）打开。
!-------------------------------------------------------------------------! ! ***** CELL LOCATING DATA ***** ! !-------------------------------------------------------------------------! RLLOC:CELL=Z12XTG1, BSPWR=52, BSTXPWR=52, BSRXMIN=115, BSRXSUFF=0,
MSRXMIN=99, MSRXSUFF=0, SCHO=ON, MISSNM=3, AW=ON, HYSTSEP=75; RLLOC:CELL=Z12XTG2, BSPWR=52, BSTXPWR=52, BSRXMIN=115, BSRXSUFF=0,
MSRXMIN=99, MSRXSUFF=0, SCHO=ON, MISSNM=3, AW=ON, HYSTSEP=75; RLLOC:CELL=Z12XTG3, BSPWR=52, BSTXPWR=52, BSRXMIN=115, BSRXSUFF=0,
MSRXMIN=99, MSRXSUFF=0, SCHO=ON, MISSNM=3, AW=ON, HYSTSEP=75; BSRXSUFF=0和MSRXSUFF=0表示屏蔽了L算法。
!-------------------------------------------------------------------------! ! ***** CELL LOCATING URGENCY DATA ***** ! !-------------------------------------------------------------------------!
RLLUC:CELL=Z12XTG1, QLIMUL=55, QLIMDL=55, TALIM=61, CELLQ=HIGH; RLLUC:CELL=Z12XTG2, QLIMUL=55, QLIMDL=55, TALIM=61, CELLQ=HIGH; RLLUC:CELL=Z12XTG3, QLIMUL=55, QLIMDL=55, TALIM=61, CELLQ=HIGH;
!-------------------------------------------------------------------------! ! ***** CELL LOCATING PENALTY DATA ***** ! !-------------------------------------------------------------------------!
RLLPC:CELL=Z12XTG1, PTIMHF=10, PTIMBQ=10, PTIMTA=10, PSSHF=63, PSSBQ=63, PSSTA=63;
RLLPC:CELL=Z12XTG2, PTIMHF=10, PTIMBQ=10, PTIMTA=10, PSSHF=63, PSSBQ=63, PSSTA=63;
ISCREATE Created by 许达敏 32101880.doc Created on 11/23/2000 9:59:00 PM Page 10 of 38 RLLPC:CELL=Z12XTG3, PTIMHF=10, PTIMBQ=10, PTIMTA=10, PSSHF=63, PSSBQ=63, PSSTA=63;
!-------------------------------------------------------------------------! ! ***** CELL LOCATING FILTER DATA ***** ! !-------------------------------------------------------------------------!
RLLFC:CELL=Z12XTG1, SSEVALSD=6, QEVALSD=6, SSEVALSI=6, QEVALSI=6,
SSLENSD=10, QLENSD=12, SSLENSI=10, QLENSI=12, SSRAMPSD=5, SSRAMPSI=5; RLLFC:CELL=Z12XTG2, SSEVALSD=6, QEVALSD=6, SSEVALSI=6, QEVALSI=6,
SSLENSD=10, QLENSD=12, SSLENSI=10, QLENSI=12, SSRAMPSD=5, SSRAMPSI=5; RLLFC:CELL=Z12XTG3, SSEVALSD=6, QEVALSD=6, SSEVALSI=6, QEVALSI=6,
SSLENSD=10, QLENSD=12, SSLENSI=10, QLENSI=12, SSRAMPSD=5, SSRAMPSI=5;
!-------------------------------------------------------------------------! ! ***** CELL LOCATING DISSCONNECT DATA ***** ! !-------------------------------------------------------------------------!
RLLDC:CELL=Z12XTG1, MAXTA=63, RLINKUP=16; RLLDC:CELL=Z12XTG2, MAXTA=63, RLINKUP=16; RLLDC:CELL=Z12XTG3, MAXTA=63, RLINKUP=16;
!-------------------------------------------------------------------------! ! ***** LOCATING HIERARCHICAL ***** ! !-------------------------------------------------------------------------! RLLHC:CELL=Z12XTG1, LEVEL=2, LEVTHR=95, LEVHYST=2, PSSTEMP=2, PTIMTEMP=5, FASTMSREG=ON;
RLLHC:CELL=Z12XTG2, LEVEL=2, LEVTHR=95, LEVHYST=2, PSSTEMP=2, PTIMTEMP=5, FASTMSREG=ON;
RLLHC:CELL=Z12XTG3, LEVEL=2, LEVTHR=95, LEVHYST=2, PSSTEMP=2, PTIMTEMP=5, FASTMSREG=ON;
微蜂窝、一般小区、宏小区的LEVEL一般分别是1、2、3。
!-------------------------------------------------------------------------! ! ***** CELL LOCATING OVERLAID SUBCELL ***** ! !-------------------------------------------------------------------------! 目前在广东省没有用OVERLAID SUBCELL（2000/11/27） ! NO OVERLAID SUBCELL STRUCTURE !
! RLOLC:CELL=CELL, LOL=LOL, LOLHYST=LOLHYST,TAOL=TAOL, ! ! TAOLHYST=TAOLHYST; ! ! NO OVERLAID SUBCELL STRUCTURE !
! RLOLC:CELL=CELL, LOL=LOL, LOLHYST=LOLHYST,TAOL=TAOL, ! ! TAOLHYST=TAOLHYST; ! ! NO OVERLAID SUBCELL STRUCTURE !