ISCREATE Created by 许达敏 32101880.doc Created on 11/23/2000 9:59:00 PM Page 11 of 38 ! RLOLC:CELL=CELL, LOL=LOL, LOLHYST=LOLHYST,TAOL=TAOL, ! ! TAOLHYST=TAOLHYST; !
!-------------------------------------------------------------------------! ! ***** CELL LOCATING INTRACELL HANDOVER ***** ! !-------------------------------------------------------------------------!
RLIHC:CELL=Z12XTG1, IHO=ON, MAXIHO=3, TMAXIHO=6, TIHO=10, SSOFFSETULN=0, SSOFFSETDLP=0, QOFFSETULP=0, QOFFSETDLP=0;
RLIHC:CELL=Z12XTG2, IHO=ON, MAXIHO=3, TMAXIHO=6, TIHO=10, SSOFFSETULN=0, SSOFFSETDLP=0, QOFFSETULP=0, QOFFSETDLP=0;
RLIHC:CELL=Z12XTG3, IHO=ON, MAXIHO=3, TMAXIHO=6, TIHO=10, SSOFFSETULN=0, SSOFFSETDLP=0, QOFFSETULP=0, QOFFSETDLP=0;
!-------------------------------------------------------------------------! ! ***** SYSTEM INFORMATION SACCH AND BCCH ***** ! !-------------------------------------------------------------------------!
RLSSC:CELL=Z12XTG1, ACCMIN=100, CCHPWR=33, CRH=4, DTXU=1, NECI=0, RLINKT=16, MBCR=0, NCCPERM=6;
RLSSC:CELL=Z12XTG2, ACCMIN=100, CCHPWR=33, CRH=4, DTXU=1, NECI=0, RLINKT=16, MBCR=0, NCCPERM=6;
RLSSC:CELL=Z12XTG3, ACCMIN=100, CCHPWR=33, CRH=4, DTXU=1, NECI=0, RLINKT=16, MBCR=0, NCCPERM=6; 注意NCCPERM对于中国电信要等于6。
!-------------------------------------------------------------------------! ! ***** SYSTEM INFORMATION BCCH ***** ! !-------------------------------------------------------------------------!
RLSBC:CELL=Z12XTG1, CB=NO, ACC=CLEAR,
MAXRET=7, TX=50, ATT=YES, T3212=5, CBQ=HIGH, CRO=0, TO=0, PT=0, ECSC=NO; RLSBC:CELL=Z12XTG2, CB=NO, ACC=CLEAR,
MAXRET=7, TX=50, ATT=YES, T3212=5, CBQ=HIGH, CRO=0, TO=0, PT=0, ECSC=NO; RLSBC:CELL=Z12XTG3, CB=NO, ACC=CLEAR,
MAXRET=7, TX=50, ATT=YES, T3212=5, CBQ=HIGH, CRO=0, TO=0, PT=0, ECSC=NO;
这里主要定义的是手机在空闲模式下小区重选的数据，还有周期性登记的数据（T3212表示周期性登记的时间，以5分钟为单位；ATT表示是否允许IMSI ATTATH和DETATH）。
ISCREATE Created by 许达敏 32101880.doc Created on 11/23/2000 9:59:00 PM Page 12 of 38
!-------------------------------------------------------------------------! ! ***** DYNAMIC MS POWER CONTROL CELL ***** ! !-------------------------------------------------------------------------! 定义手机动态功率控制参数。
RLPCC:CELL=Z12XTG1, SSDES=80, INIDES=70, SSLEN=5, INILEN=2,
PMARG=4, QLEN=4, LCOMPUL=50, QCOMPUL=30, REGINT=5, DTXFUL=5, QDESUL=35;
RLPCC:CELL=Z12XTG2, SSDES=80, INIDES=70, SSLEN=5, INILEN=2,
PMARG=4, QLEN=4, LCOMPUL=50, QCOMPUL=30, REGINT=5, DTXFUL=5, QDESUL=35;
RLPCC:CELL=Z12XTG3, SSDES=80, INIDES=70, SSLEN=5, INILEN=2,
PMARG=4, QLEN=4, LCOMPUL=50, QCOMPUL=30, REGINT=5, DTXFUL=5, QDESUL=35;
RLPCI:CELL=Z12XTG1; RLPCI:CELL=Z12XTG2; RLPCI:CELL=Z12XTG3;
RLPCI表示打开手机动态功率控制。（RLPCE用来关掉手机动态功率控制）
!-------------------------------------------------------------------------! ! ***** DYNAMIC BTS POWER CONTROL CELL ***** ! !-------------------------------------------------------------------------! 定义基站动态功率控制参数。
RLBCC:CELL=Z12XTG1, SDCCHREG=ON, SSDESDL=80, SSLENDL=5,
LCOMPDL=50, QCOMPDL=30, QLENDL=12, REGINTDL=5, BSPWRMINN=20, QDESDL=35;
RLBCC:CELL=Z12XTG2, SDCCHREG=ON, SSDESDL=80, SSLENDL=5,
LCOMPDL=50, QCOMPDL=30, QLENDL=12, REGINTDL=5, BSPWRMINN=20, QDESDL=35;
RLBCC:CELL=Z12XTG3, SDCCHREG=ON, SSDESDL=80, SSLENDL=5,
LCOMPDL=50, QCOMPDL=30, QLENDL=12, REGINTDL=5, BSPWRMINN=20, QDESDL=35;
RLBCI:CELL=Z12XTG1; RLBCI:CELL=Z12XTG2; RLBCI:CELL=Z12XTG3;
RLPCI表示打开基站动态功率控制。（RLPCE用来关掉基站动态功率控制）
!-------------------------------------------------------------------------! ! ***** DIFFERENTIAL CHANNEL ALLOCATION ***** ! !-------------------------------------------------------------------------!
ISCREATE Created by 许达敏 32101880.doc Created on 11/23/2000 9:59:00 PM Page 13 of 38 ! RLPRC:CELL=Z12XTG1, CHTYPE=SDCCH, PP=DEFAULT; ! ! RLPRC:CELL=Z12XTG1, CHTYPE=TCH, CHRATE=FR, PP=DEFAULT; ! ! RLPRC:CELL=Z12XTG1, CHTYPE=TCH, CHRATE=HR, PP=DEFAULT; ! ! RLPRC:CELL=Z12XTG2, CHTYPE=SDCCH, PP=DEFAULT; ! ! RLPRC:CELL=Z12XTG2, CHTYPE=TCH, CHRATE=FR, PP=DEFAULT; ! ! RLPRC:CELL=Z12XTG2, CHTYPE=TCH, CHRATE=HR, PP=DEFAULT; ! ! RLPRC:CELL=Z12XTG3, CHTYPE=SDCCH, PP=DEFAULT; ! ! RLPRC:CELL=Z12XTG3, CHTYPE=TCH, CHRATE=FR, PP=DEFAULT; ! ! RLPRC:CELL=Z12XTG3, CHTYPE=TCH, CHRATE=HR, PP=DEFAULT; !
!-------------------------------------------------------------------------! ! ***** SUPERVISION OF LOGICAL CHANNEL AVAILABILITY ***** ! !-------------------------------------------------------------------------! RLSLC:CELL=Z12XTG1, LVA=5, ACL=A3, CHTYPE=TCH, CHRATE=FR; RLSLC:CELL=Z12XTG1, LVA=1, ACL=A2, CHTYPE=SDCCH; RLSLC:CELL=Z12XTG1, LVA=1, ACL=A1, CHTYPE=BCCH; RLSLC:CELL=Z12XTG1, LVA=0, ACL=A2, CHTYPE=CBCH;
RLSLC:CELL=Z12XTG2, LVA=5, ACL=A3, CHTYPE=TCH, CHRATE=FR; RLSLC:CELL=Z12XTG2, LVA=1, ACL=A2, CHTYPE=SDCCH; RLSLC:CELL=Z12XTG2, LVA=1, ACL=A1, CHTYPE=BCCH; RLSLC:CELL=Z12XTG2, LVA=0, ACL=A2, CHTYPE=CBCH;
RLSLC:CELL=Z12XTG3, LVA=5, ACL=A3, CHTYPE=TCH, CHRATE=FR; 表示有5个TCH损坏就会发生A3告警（实际上只要有1个TCH损坏就表示这个小区有问题了，所以这里最好LVA=1）
RLSLC:CELL=Z12XTG3, LVA=1, ACL=A2, CHTYPE=SDCCH; 表示有1个SDCCH损坏就会发生A2告警
RLSLC:CELL=Z12XTG3, LVA=1, ACL=A1, CHTYPE=BCCH;
表示有1个BCCH损坏就会发生A1告警（BCCH损坏通常表示这个小区已经不能用了） RLSLC:CELL=Z12XTG3, LVA=0, ACL=A2, CHTYPE=CBCH; 定义信道的监测告警门限。LVA表示有多少个信道损坏就会发生ACL类告警。有时候在减少载波后没有更改TCH的告警门限，告警会不断的出来。这时需要更改这个LVA值，同时用RLSLE、RLSLC重新定义告警门限，就可以把告警消掉
!-------------------------------------------------------------------------! ! ***** IDLE CHANNEL MEASUREMENT ***** ! !-------------------------------------------------------------------------! RLIMC:CELL=Z12XTG1, INTAVE=6, LIMIT1=4, LIMIT2=8, LIMIT3=15, LIMIT4=25; RLIMC:CELL=Z12XTG2, INTAVE=6, LIMIT1=4, LIMIT2=8, LIMIT3=15, LIMIT4=25; RLIMC:CELL=Z12XTG3, INTAVE=6, LIMIT1=4, LIMIT2=8, LIMIT3=15, LIMIT4=25; 注意LIMIT1 ! RLIMI:CELL=Z12XTG1; SERVICE IS PASSIVE ! ! RLIMI:CELL=Z12XTG2; SERVICE IS PASSIVE ! ! RLIMI:CELL=Z12XTG3; SERVICE IS PASSIVE ! RLIMI是用来激活小区空闲模式下的测量，可以用来检查是否有干扰（激活后用RLCRP可以从 ISCREATE Created by 许达敏 32101880.doc Created on 11/23/2000 9:59:00 PM Page 14 of 38 ICMBAND的参数看是否有干扰，等于1是正常，5是最糟糕） !-------------------------------------------------------------------------! ! ***** CELL LOAD SHARING ***** ! !-------------------------------------------------------------------------! 目前广东省没有用这种功能（CELL LOAD SHARING是如果一个小区A话务量不大而另一个小区B话务量却很大时，A小区可以分担B小区的话务量。和用KOFFSET的调节方法不同，KOFFSET是通过改变小区边界来调节话务量的）。这里只是把参数设置一下，并没有激活功能。 RLLCC:CELL=Z12XTG1, CLSLEVEL=20, CLSACC=40, HOCLSACC=OFF, RHYST=75, CLSRAMP=16; RLLCC:CELL=Z12XTG2, CLSLEVEL=20, CLSACC=40, HOCLSACC=OFF, RHYST=75, CLSRAMP=16; RLLCC:CELL=Z12XTG3, CLSLEVEL=20, CLSACC=40, HOCLSACC=OFF, RHYST=75, CLSRAMP=16; ! RLLCI:CELL=Z12XTG1; SERVICE NOT ACTIVE ! ! RLLCI:CELL=Z12XTG2; SERVICE NOT ACTIVE ! ! RLLCI:CELL=Z12XTG3; SERVICE NOT ACTIVE ! !-------------------------------------------------------------------------! ! ***** RADIO CONTROL CELL MULTIPLE CHANNEL ALLOCATION DATA ***** ! !-------------------------------------------------------------------------! ! ONLY IF FUNCTIONALITY IS SUPPORTED BY THE EXCHANGE ! ! RLCDC:CELL=Z12XTG1, MC=OFF; (BSCMC=OFF) ! ! RLCDC:CELL=Z12XTG2, MC=OFF; (BSCMC=OFF) ! ! RLCDC:CELL=Z12XTG3, MC=OFF; (BSCMC=OFF) ! !-------------------------------------------------------------------------! ! ***** RADIO CONTROL CELL ADAPTIVE CONFIGURATION ***** ! !-------------------------------------------------------------------------! ! RLACC:CELL=Z12XTG1, STIME=20, SLEVEL=0; NOT INITIATED ! ! RLACC:CELL=Z12XTG2, STIME=20, SLEVEL=0; NOT INITIATED ! ! RLACC:CELL=Z12XTG3, STIME=20, SLEVEL=0; NOT INITIATED ! ! RLACI:CELL=Z12XTG1; NOT ACTIVATED ! ! RLACI:CELL=Z12XTG2; NOT ACTIVATED ! ! RLACI:CELL=Z12XTG3; NOT ACTIVATED ! !-------------------------------------------------------------------------! ! ***** RADIO CONTROL CELL SUBCELL LOAD DISTRIBUTION DATA ***** ! !-------------------------------------------------------------------------! ISCREATE Created by 许达敏 32101880.doc Created on 11/23/2000 9:59:00 PM Page 15 of 38 ! RLLLC:CELL=Z12XTG1,SCLD=OFF,SCLDLL=20,SCLDUL=30; NO SUBCELL ! ! RLLLC:CELL=Z12XTG2,SCLD=OFF,SCLDLL=20,SCLDUL=30; NO SUBCELL ! ! RLLLC:CELL=Z12XTG3,SCLD=OFF,SCLDLL=20,SCLDUL=30; NO SUBCELL ! !-------------------------------------------------------------------------! ! ***** RADIO CONTROL CELL HANDOVER POWER BOOST ***** ! !-------------------------------------------------------------------------! ! RLPBI:CELL=Z12XTG1; NOT ACTIVATED ! ! RLPBI:CELL=Z12XTG2; NOT ACTIVATED ! ! RLPBI:CELL=Z12XTG3; NOT ACTIVATED ! !$$$$ !86000,1! !Neighbouring Cell Data! !-------------------------------------------------------------------------! ! ***** NEIGHBOURING CELL DATA, CELL MENGWEI ***** ! ! ***** DEFINITION OF CELL MEASUREMENT FREQUENCIES ***** ! !-------------------------------------------------------------------------! RLMFC:CELL=Z12XTG1, MBCCHNO=53&88&71&62&81&79&80&88; RLMFC:CELL=Z12XTG2, MBCCHNO=84&88&90&75&79; RLMFC:CELL=Z12XTG3, MBCCHNO=84&53&73&71&90; 定义测量频点（相邻小区的BCCH频点），千万不要定错，否则等于少了一个邻区。空闲模式（IDLE）可专用模式（ACTIVE）是可以有不同的测量频点的。加上MRNIC参数可以缩短LOAD入的时间（推荐，特别是删掉测量频点时很有用）。 !-------------------------------------------------------------------------! ! ***** DEFINITION OF NEIGHBOURING CELL DATA ***** ! ! ***** NEIGHBOURS TO CELL : MENGWEI ***** ! !-------------------------------------------------------------------------! RLNRI:CELL=Z12XTG1, CELLR=Z12XTG2; RLNRI:CELL=Z12XTG1, CELLR=Z12XTG3; RLNRI:CELL=Z12XTG1, CELLR=Z12XTB2; RLNRI:CELL=Z12XTG1, CELLR=Z12DDN2; RLNRI:CELL=Z12XTG1, CELLR=Z12GHU2; RLNRI:CELL=Z12XTG1, CELLR=Z12JJS1; RLNRI:CELL=Z12XTG1, CELLR=Z12XTX0; RLNRI:CELL=Z12XTG1, CELLR=DGAJNN4,SINGLE; 定义外部小区要加入SINGLE参数。