forklift叉车
trailer=long vehicle拖板车 compound die合模 die locker锁模器
pressure plate=plate pinch压板 bolt螺栓
name of a department部门名称
administration/general affairs dept总务部 automatic screwdriver电动启子 thickness gauge厚薄规 gauge(or jig)治具 power wire电源线 buzzle蜂鸣器
defective product label不良标签 identifying sheet list标示单 screwdriver holder起子插座 pedal踩踏板 stopper阻挡器 flow board流水板
hydraulic handjack油压板车 forklift叉车 pallet栈板 glove(s)手套
glove(s) with exposed fingers割手套 thumb大拇指 forefinger食指 midfinger中指 ring finger无名指 little finger小指 band-aid创可贴
iudustrial alcohol工业酒精 alcohol container沾湿台 head of screwdriver起子头 sweeper扫把 mop拖把
vaccum cleaner吸尘器 rag 抹布
garbage container灰箕 garbage can垃圾箱 garbage bag垃圾袋 chain链条 jack升降机
production line流水线 chain链条槽 magnetizer加磁器 lamp holder灯架 to mop the floor拖地
to clean the floor扫地 to clean a table擦桌子 air pipe 气管 packaging tool打包机 packaging打包 missing part漏件 wrong part错件
excessive defects过多的缺陷 critical defect极严重缺陷 major defect主要缺陷 minor defect次要缺陷 not up to standard不合规格
dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良
slipped screwhead/slippery screw head螺丝滑头 slipped screwhead/shippery screw thread滑手 speckle斑点
mildewed=moldy=mouldy发霉 rust生锈 deformation变形 burr(金属)flash(塑件)毛边 poor staking铆合不良 excesssive gap间隙过大 grease/oil stains油污 inclusion杂质 painting peel off脏污 shrinking/shrinkage缩水 mixed color杂色 scratch划伤
poor processing 制程不良 poor incoming part事件不良 fold of pakaging belt打包带折皱 painting make-up补漆 discoloration羿色 water spots水渍
polishing/surface processing表面处理 exposed metal/bare metal金属裸露 lack of painting烤漆不到位 safety安全 quality品质
delivery deadline交货期 cost成本 engineering工程 die repair模修
enterprise plan = enterprise expansion projects企划QC品管 die worker模工
production, to produce生产 equipment设备 to start a press开机 stop/switch off a press关机 classification整理 regulation整顿 cleanness清扫 conservation清洁 culture教养
qualified products, up-to-grade products良品 defective products, not up-to-grade products不良品waste废料
shut height of a die架模高度 analog-mode device类模器 die lifter举模器 argon welding氩焊 vocabulary for stamping 冲压常词汇 stamping, press冲压
punch press, dieing out press冲床 uncoiler & strainghtener整平机 feeder送料机 rack, shelf, stack料架 cylinder油缸 robot机械手 taker取料机 conveyer belt输送带 transmission rack输送架 top stop上死点 bottom stop下死点 one stroke一行程 inch寸动
to continue, cont.连动 to grip(material)吸料
location lump, locating piece, block stop 定位块 reset复位 smoothly顺利 dent压痕 scratch刮伤 deformation变形 filings铁削 to draw holes抽孔 inquiry, search for查寻 to stock, storage, in stock库存 receive领取
approval examine and verify审核 processing, to process加工
delivery, to deliver 交货
to return delivenry to. to send delinery back to retrn of goods退货 registration登记 registration card登记卡 to control管制
to put forward and hand in提报 safe stock安全库存 acceptance = receive验收 to notice通知
application form for purchase请购单 consume, consumption消耗 to fill in填写 abrasion磨损
reverse angle = chamfer倒角 character die字模 to collect, to gather收集 failure, trouble故障 statistics统计
demand and supply需求 career card履历卡 to take apart a die卸下模具 to load a die装上模具 to tight a bolt拧紧螺栓 to looser a bolt拧松螺栓
to move away a die plate移走模板 easily damaged parts易损件 standard parts标准件
breaking.(be)broken,(be)cracked 断裂 to lubricate润滑
common vocabulary for die engineering模具工程常用词汇 die 模具
figure file, chart file图档 cutting die, blanking die冲裁模 progressive die, follow (-on)die 连续模
compound die复合模 punched hole冲孔 panel board镶块
to cutedges=side cut=side scrap切边 to bending折弯 to pull, to stretch拉伸
Line streching, line pulling线拉伸 engraving, to engrave刻印 upsiding down edges翻边 to stake铆合
designing, to design设计
design modification设计变化 die block模块 folded block折弯块 sliding block滑块 location pin定位销 lifting pin顶料销 die plate, front board模板 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring 弹簧 bolt螺栓
document folder活页夹 file folder资料夹
to put file in order整理资料 spare tools location手工备品仓 first count初盘人 first check初盘复棹人 second count 复盘人 second check复盘复核人 equipment设备 waste materials废料
work in progress product在制品 casing = containerazation装箱
quantity of physical invetory second count 复盘点数量quantity of customs count 会计师盘,点数量 the first page第一联
filed by accounting department for reference会计部存查
end-user/using unit(department)使用单位 summary of year-end physical inventory bills 年终盘点截止单据汇总表 bill name单据名称
This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)
本表请与盘点清册一起送会计部－(NHK厂区送财会部)
Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表 blank and waste sheet NO. 空白与作废单号
plate电镀 mold成型
material for engineering mold testing工程试模材料 not included in physical inventory不列入盘点 sample样品
incoming material to be inspected进货待验 description品名 入水：gate
进入位： gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size
转水口： switching runner/gate 唧嘴口径： sprue diameter 二、流道: runner
热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴： hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头： connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube
快速接头：jiffy quick connector plug/socker 四、模具零件： mold components 三板模：3-plate mold 二板模：2-plate mold
边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin
顶针板：ejector retainner plate 托板： support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot
内模管位：core/cavity inter-lock
顶针： ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate
缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter
模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜鸡：wedge
耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch
扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring
中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch
adjustable spanner 活动扳手 angle cutter 角铣刀 anvil 铁钻 arbour 心轴
backing 衬垫 belt sander 带式打磨机 buffing 抛光 chamfering machine 倒角机 chamfering tool 去角刀具 chisel 扁錾 chuck 夹具 compass 两角规
concave cutter 凹面铣刀 convex cutter 凸形铣刀 cross joint 十字接头 cutting edge clearance 刃口余隙角
drill stand 钻台 edge file 刃用锉刀 file 锉刀 flange joint 凸缘接头
grinder 砂轮机 hammer 铁锤 hand brace 手摇钻 hatching 剖面线
hexagon headed bolt 六角头螺栓 hexagon nut 六角螺帽
index head 分度头 jack 千斤顶 jig 治具 kit 工具箱
lapping 研磨 metal saw 金工锯 nose angle 刀角 pinchers 钳子 pliers 铗钳 plug 柱塞头
polisher 磨光器 protable driller 手提钻孔机 punch 冲头 sand paper 砂纸 scraper 刮刀 screw driver 螺丝起子 scribing 划线 second out file 中纹锉 spanner 扳手 spline broach 方栓槽拉刀 square 直角尺 square sleeker 方形镘刀 square trowel 直角度 stripping 剥离工具 T-slot T形槽 tool for lathe 车刀 tool point angle 刀刃角 tool post 刀架 tosecan 划线盘 trimming 去毛边
waffle die flattening 压纹效平 wiper 脱模钳 wrench 螺旋扳手
aberration 色差 atomization 霚化 bank mark 滞料纹 bite 咬入
blacking hole 涂料孔(铸疵) blacking scab 涂料疤 blister 起泡 blooming 起霜 blow hole 破孔 blushing 泛白
body wrinkle 侧壁皱纹 breaking-in 冒口带肉 bubble 膜泡 burn mark 糊斑 burr 毛边 camber 翘曲
cell 气泡 center buckle 表面中部波皱 check 细裂痕 checking 龟裂
chipping 修整表面缺陷 clamp-off 铸件凹痕 collapse 塌陷 color mottle 色斑 corrosion 腐蚀 crack 裂痕 crazing 碎裂 crazing 龟裂 deformation 变形 edge 切边碎片 edge crack 裂边 fading 退色 filler speak 填充料斑 fissure 裂纹 flange wrinkle 凸缘起皱 flaw 刮伤 flow mark 流痕 galling 毛边 glazing 光滑 gloss 光泽
grease pits 污斑 grinding defect 磨痕 haircrack 发裂 haze 雾度 incrustation 水锈 indentation 压痕 internal porosity 内部气孔 mismatch 偏模 mottle 斑点 necking 缩颈
nick 割痕 orange peel 橘皮状表面缺陷
overflow 溢流 peeling 剥离 pit 坑 pitting corrosion 点状腐蚀 plate mark 模板印痕 pock 麻点 pock mark 痘斑 resin streak 树脂流纹 resin wear 树脂脱落 riding 凹陷 sagging 松垂 saponification 皂化 scar 疤痕 scrap 废料
scrap jam 废料阻塞 scratch 刮伤/划痕 scuffing 深冲表面划伤 seam 裂痕 shock line 模口挤痕 short shot 充填不足 shrinkage pool 凹孔 sink mark 凹痕 skin inclusion 表皮折迭 straightening 矫直 streak 条状痕 surface check 表面裂痕
surface roughening 橘皮状表皮皱折 surging 波动 sweat out 冒汗 torsion 扭曲 warpage 翘曲 waviness 波痕 webbing 熔塌 weld mark 焊痕 whitening 白化 wrinkle 皱纹
age hardening 时效硬化 ageing 老化处理 air hardening 气体硬化 air patenting 空气韧化 annealing 退火 anode effect 阳极效应
anodizing 阳极氧化处理 atomloy treatment 阿扥木洛伊表面
austempering 奥氏体等温淬火 austenite 奥斯田体/奥氏体
bainite 贝氏体 banded structure 条纹状组织 barrel plating 滚镀 barrel tumbling 滚筒打光 blackening 染黑法 blue shortness 青熟脆性
bonderizing 磷酸盐皮膜处理 box annealing 箱型退火 box carburizing 封箱渗碳 bright electroplating 辉面电镀
bright heat treatment 光辉热处理 bypass heat treatment 旁路热处理
carbide 炭化物 carburized case depth 浸碳硬化深层 carburizing 渗碳 cementite 炭化铁
chemical plating 化学电镀 chemical vapor deposition 化学蒸镀
coarsening 结晶粒粗大化 coating 涂布被覆 cold shortness 低温脆性 comemtite 渗碳体 controlled atmosphere 大气热处理 corner effect 锐角效应
creeping discharge 蠕缓放电 decarburization 脱碳处理 decarburizing 脱碳退火 depth of hardening 硬化深层 diffusion 扩散 diffusion annealing 扩散退火 electrolytic hardening 电解淬火 embossing 压花 etching 表面蚀刻 ferrite 肥粒铁
first stage annealing 第一段退火 flame hardening 火焰
硬化
flame treatment 火焰处理 full annealing 完全退火 gaseous cyaniding 气体氧化法 globular cementite 球状炭化铁
grain size 结晶粒度 granolite treatment 磷酸溶液热处理
graphitizing 石墨退火 hardenability 硬化性 hardenability curve 硬化性曲线 hardening 硬化 heat treatment 热处理 hot bath quenching 热浴淬火 hot dipping 热浸镀 induction hardening 高周波硬化 ion carbonitriding 离子渗碳氮化 ion carburizing 离子渗碳处理
ion plating 离子电镀 isothermal annealing 等温退火 liquid honing 液体喷砂法 low temperature annealing 低温退火
malleablizing 可锻化退火 martempering 麻回火处理 martensite 马氏体/硬化铁炭 metallikon 金属喷镀法 metallizing 真空涂膜 nitriding 氮化处理 nitrocarburizing 软氮化 normalizing 正常化 oil quenching 油淬化 overageing 过老化 overheating 过热 pearlite 针尖组织 phosphating 磷酸盐皮膜处理 physical vapor deposition 物理蒸镀