DTGH-D-043-MG3000-T4-串口控制台使用手册
2 -- set MTP2 proving mode 3 -- display MTP2 configuration : 1
Please input timer 1 value (400 ~ 500) [ 400 ] <100ms> : Please input timer 2 value (50 ~ 150) [ 50 ] <100ms> : Please input timer 3 value (10 ~ 20) [ 10 ] <100ms> : Please input timer 4 normal value (75 ~ 95) [ 82 ] <100ms> : Please input timer 4 emergence value (4 ~ 6) [ 5 ] <100ms> : Please input timer 5 value (1 ~ 2) [ 1 ] <100ms> : Please input timer 6 value (30 ~ 60) [ 50 ] <100ms> : Please input timer 7 value (5 ~ 20) [ 10 ] <100ms> : The command has been completed successfully!
6.3 配置MTP2定位验收模式
可以修改MTP2定位验收模式，会影响链路建立时验收时间长度，例如： MG3000-T4:\\PSTN> mtp2 Please input operation
1 -- set MTP2 timer value 2 -- set MTP2 proving mode 3 -- display MTP2 configuration : 2
MTP2 proving mode (0 -- Normal, 1 -- Emergency) [ 0 ] : The command has been completed successfully!
6.4 显示MTP2定时器和定位验收模式
显示MTP2定时器值和定位验收模式，例如： MG3000-T4:\\PSTN> mtp2 Please input operation
1 -- set MTP2 timer value 2 -- set MTP2 proving mode 3 -- display MTP2 configuration : 3 MTP2 timer 1 value : 40000 ms
GoHigh http://www.gohigh.com.cn 20
DTGH-D-043-MG3000-T4-串口控制台使用手册
MTP2 timer 2 value : 5000 ms MTP2 timer 3 value : 1000 ms MTP2 timer 4 normal value : 8200 ms MTP2 timer 4 emergency value : 500 ms MTP2 timer 5 value : 100 ms MTP2 timer 6 value : 5000 ms MTP2 timer 7 value : 1000 ms MTP2 proving mode : Normal
The command has been completed successfully!
6.5 配置链路
可以添加或删除链路。添加链路时，需要依次输入的是链路所在E1端口号、时隙号、OPC、RPC、SLC。删除链路只需输入所要删除的链路号，但必须保证该链路已去活且不被链路集包含。例如：
MG3000-T4:\\PSTN> mtp3 Please input operation 1 -- configure link 2 -- configure linkset 3 -- configure route 4 -- configure circuit 5 -- activate or deactivate link
6 -- display MTP3 configuration and status 7 -- set MTP3 timer value : 1 Please input operation 1 -- add link 2 -- delete link : 1
Please input E1 port number (1 ~ 4) : 1 Please input the timeslot number (1 ~ 31) : 16 Please input the OPC netID (0 ~ 255) : 1
GoHigh http://www.gohigh.com.cn 21
DTGH-D-043-MG3000-T4-串口控制台使用手册
Please input the OPC cluster (0 ~ 255) : 8 Please input the OPC member (0 ~ 255) : 9 Please input the RPC netID (0 ~ 255) : 1 Please input the RPC cluster (0 ~ 255) : 0 Please input the RPC member (0 ~ 255) : 5 Please input the SLC (0 ~ 255) : 0
The command has been completed successfully!
6.6 配置链路集
可以添加或删除链路集。添加链路集时，只需输入所要包含的链路号，包含多个链路时以逗号分隔，被包含的链路必须已定义。删除链路集只需输入所要删除的链路集号，但必须保证该链路集包含的链路已去活且该链路集不被路由包含。例如：
MG3000-T4:\\PSTN> mtp3 Please input operation 1 -- configure link 2 -- configure linkset 3 -- configure route 4 -- configure circuit 5 -- activate or deactivate link
6 -- display MTP3 configuration and status 7 -- set MTP3 timer value : 2 Please input operation 1 -- add linkset 2 -- delete linkset : 1
Please input link id included (0 ~ 3, seperated by ,) : 0 The command has been completed successfully!
6.7 配置路由
可以添加或删除路由。添加路由时，只需输入所要包含的链路集号，一般情况下路由都是与链路集一一对应的，被包含的链路集必须已定义。删除路由时只需输入所要删除的路由号，但必GoHigh http://www.gohigh.com.cn 22
DTGH-D-043-MG3000-T4-串口控制台使用手册
须保证该路由对应的链路集包含的链路已去活。例如：
MG3000-T4:\\PSTN> mtp3 Please input operation 1 -- configure link 2 -- configure linkset 3 -- configure route 4 -- configure circuit 5 -- activate or deactivate link
6 -- display MTP3 configuration and status 7 -- set MTP3 timer value : 3 Please input operation 1 -- add routeentry 2 -- delete routeentry : 1
Please input linkset id included (0 ~ 3, seperated by ,) : 0 The command has been completed successfully!
6.8 配置话路
可以设置CIC属性、添加或删除话路。设置的CIC属性包括非话路承载通道是否占用CIC、是否使用16时隙作为话路承载通道。添加话路时，依次输入所要添加的E1端口号、使用的路由号、CIC开始值，被包含的路由必须已定义。删除话路时只需输入所要删除的E1端口号，但必须保证该E1端口使用的路由对应链路集包含的链路已去活。例如：
Trunk-GW:\\PSTN> mtp3 Please input operation 1 -- configure link 2 -- configure linkset 3 -- configure route 4 -- configure circuit 5 -- activate or deactivate link
6 -- display MTP3 configuration and status
GoHigh http://www.gohigh.com.cn 23
DTGH-D-043-MG3000-T4-串口控制台使用手册
7 -- set MTP3 timer value : 4 Please input operation 1 -- set CIC attribute 2 -- add circuit 3 -- delete circuit : 1
Whether Non-bearer channel occupy CIC(0 -- No; 1 -- Yes)[ 1 ] : Whether TS16 is used for bearer channel allocation(0 -- No; 1 -- Yes)[ 1 ] : The command has been completed successfully!
MG3000-T4:\\PSTN> mtp3 Please input operation 1 -- configure link 2 -- configure linkset 3 -- configure route 4 -- configure circuit 5 -- activate or deactivate link
6 -- display MTP3 configuration and status 7 -- set MTP3 timer value : 4 Please input operation 1 -- set CIC attribute 2 -- add circuit 3 -- delete circuit : 2 Please input the E1 port id (1 ~ 4) : 1
Please input the route entry id E1 port 1 attachs to : 0 Please input the CIC base of E1 port 1 : 0 The command has been completed successfully!
6.9 激活链路
可以激活或去活链路。只需输入要激活或去活的链路号。激活链路前，必须保证该链路、相GoHigh http://www.gohigh.com.cn 24