--(报警设置为所有的模拟量输出为0%)
Alarm limit for analog input N2ACTEXH 6 at 15.0 slm at 0 % (?0.0) --(报警的设置为模拟量补偿氮为0%时)
Alarm on digital in N2 PRESS[1] = ON,AIRPRESS[2] = ON,DOORCLSD[3] = OFF,REAREXH[4] = ON,UPSPOWER[5] = ON,UPS
LOW[6] = ON,TEMP SCR[7] = ON,OVERHEAT[8] = ON
--(报警为数字量输入N2压力为打开，空气压力为打开，炉门为关闭，酸排为打开，UPS电源为打开，UPS低电压为打开，SCR温度为打开，过温度为打开) Alarm on digital in FANSWTCH[9] = ON,TEMPPOCL[10] = ON,LEVLPOCL[11] = ON,CUSTALRM[12] = ON,HEATEXCH[13] = ON,R2DALARM[14] = OFF,*START[15] = OFF,*LDINR2D[16] = OFF
--(报警为数字量风扇开关为打开，POCL温度为打开，POCL水平为打开，CUSTALRM为打开，HEATEXCH[13] = ON,R2DALARM[14] = OFF,*START[15] = OFF,*LDINR2D[16] = OFF) Wait for operator --(等待操作人员) 13 RETURN
--(返回)
Branch always to step LOAD/UNLOAD. Sonalert alarm No --(通常分流到LOAD/UNLOAD这步) 14 BOAT RETURN UP
Message BOAT OUT [3]. Sonalert alarm No
--(舟出)
Time: 000:08:00 (hr:min:sec) Variable Command: No --(时间为8分钟)
Normal recipe 00 Zone1 800.0 癈 Slope 10.00 癈/min Zone2 800.0 癈 Slope 10.00 癈/min Zone3 800.0癈 Slope 10.00 癈/min Zone4 800.0 癈 Slope 10.00 癈/min Zone5 800.0 癈 Slope 10.00 癈/min ,profile table A --(温度存储在NR00, 第一区的温度为800℃，第二区的温度为800℃，第三区的温度为800℃，第四区的温度为800℃，第五区的温度为800℃,拉温的数据存储在TableA中) Boat to 20.0 mm at 600.0 mm/min with oscillation speed of 10.0 mm/min. Variable Command: No --(打开炉门) Wait for operator --(等待操作人员)
Wait for boat to reach setpoint --(等待舟回到设置点) Abort recipe 03 --(Abort 程序为03) 15 RETURN
--(返回)
Branch always to step LOAD/UNLOAD. Sonalert alarm No --(通常分流到LOAD/UNLOAD这步) 16 BOAT RETURN DOWN
--(舟返回)
Message BOAT OUT [3]. Sonalert alarm No
Time: 000:08:00 (hr:min:sec) Variable Command: No --(时间为8分钟)
Normal recipe 00 Zone1 800.0 癈 Slope 10.00 癈/min Zone2 800.0 癈
Slope 10.00 癈/min Zone3 800.0癈 Slope 10.00 癈/min Zone4 800.0 癈 Slope 10.00 癈/min Zone5 800.0 癈 Slope 10.00 癈/min , profile table A --(温度存储在NR00, 第一区的温度为800℃，第二区的温度为800℃，第三区的温度为800℃，第四区的温度为800℃，第五区的温度为800℃,拉温的数据存储在Table A中) Boat to 20.0 mm at 600.0 mm/min with oscillation speed of 0.0 mm/min. Variable Command: No --(打开炉门) Wait for operator
--(等待操作人员)
Wait for boat to reach setpoint --(等待舟到达设置点) Abort recipe 02 --(Abort 程序为02)