5.2.3 Part – No. - Function
No. GAA30082AAC
29 – Apr – 94 08:29
Key Sequence
The Part – No. – Function display the current software version of the EPROM and EEPROM.
It also displays the date and the time of the LCB_II software release.
M – 1 – 2 – 3
Figure 5-13 :Part – No. – Function - Key GOON / Shift Key GOBACK: Toggle between the displays goon of the EPROM version goon and the display that shows the EPROM version and (GOBACK) the date / time of the release. clear - Key CLEAR: back to Test - Menu
3)
1) 2)
4) 1)E 1)E47NS9528
EE=E47NS9528
2)GAA 30082 AAC No. GAA30082AAC Apr – 94 08:29 29 – 3)29 – Apr – 94 4)08:29
EE=E47NS9528 No. GAA30082AAC 29 – Apr – 94 08:29 software version / date / time EEPROM version EPROM version
date and time of the release
5.2.4 RSL – Test - Function
Key Sequence
M – 1 – 2 – 4 ADR = _ _ _ _ _ _ _ _ _ _ The RSL – Test – Function can be used to test the remote Stations.
After the address of the Remote Station is entered, - the four Input Pins are monitored and - the four Output pins can be set.
Figure 5-13 : RSL / Test - Function
Enter the RSL – address
1 - Key 1,5: Input Keys of the 2 RSL - address ADR=15______________ _____________________- - Key CLEAR: deletes the last input if you want to correct clear the number. clear - Shift Key ENTER: termination of the input operation The current status of the Input – and Output pins of The entered RSL address is ADR=15 BIT = 1 displayed. IN : off OUT : off
Change address, pin and output
goon goon 2 3 1 0 clear - Key GOON / Shift Key GOBACK: Skip to the next / Previous address. - Shift Key UP / Shift Key DOWN: Skip to the next / Previous bit. - Shift Key ON / Shift Key OFF: Toggle of the Output - Pin: on / off - Key CLEAR: back to Test - Menu
RSL: Status
ADR = 16 BIT = 1 IN : off OUT : off ADR = 16 BIT = 2 IN : off OUT : off ADR = 16 BIT = 2 IN : off OUT : on 1) 2) 1) ADR 2) BIT
3) IN 4) OUT
RSL address(decimal) RSL - pin
RSL Input Pin Status (Monitor) RSL Output Pin Status
ADR = 16 BIT = 2 IN : off OUT : on 3) 4) (on = action / off = not active)
5.2.5 Selfest - Function
Key Sequence
M – 1 – 2 – 5 PR ? EE ? RA ? RS ?_ _ _ _ _ _ Function Selftest can be used
- to test the memory of the LCB_II board and - to check the Remote Serial Link. The test will start as soon as the Selftest - Function Is called.
Figure 5-14: Selftest - Function
PR + EE - RA ? RS ?_ _ _ _ _ PR + EE + RA + RS 16aR0000 RS – Remote Station Test
The flashing question mark indicates which part of the test is currently active (RA): - PR EPROM - test - EE EEPROM - test - RA RAM-test
- RS Remote Serial Link test The single results are displayed as: - (+)for Test successfully finished - ( -)for Test not successfully finished
Please notice that for the EE – test a checksum written into the EEPROM is verified .So, the first call of the test with a new EEPROM will result a (-)
The RS – test will give some information about single Remote Station.
- if they are setup but not available - if they are responding - if they are parity errors
16 A B R r
RS - test RSL - address available (IO-No. is defined) not available
responding (Hardware is okay) not responding parity error counter
PR + EE + RA + RS 16aR0000
000
goon goon clear - Key GOON / Shift Key GOBACK : Skip through the list of Remote Station which signals - not available or - not responding or - parity errors. PR + EE + RA + RS 48Ar000 __ - If there was at least one entry in the list ,the display for Test not successfully PR + EE + RA + finished ( - ) occurs. RS -_ _ _ _ _ _ - Key CLEAR: back to Test - Menu