rod guide added lubricant grease or.
Regular maintenance cycle (2) three months),
Open the Z axis, ball screw, protect clean on the rails and dirt, then gave
scraps ball screw and guide with grease or oil
Check the connecting cable connection.
Check belt wear
Chapter 11 each type machine motor parameters
After installing the software without the correct parameters Settings Axis Item TS-2518B/TS-2518C TS-3040C TS-3040C-TS-7050 TS3040B H50 X Steps 640 400 400 320 320 Per 速度 600 1200 1200 1200 2000 加速度 300 400 400 400 400 Y Steps 640 400 320 320 320 Per 速度 600 1200 1200 1200 2000 加速度 300 300 300 300 300 Z Steps 640 640 640 640 320 Per 速度 600 800 800 800 2000 加速度 300 300 300 300 300 Appendix 1: Engraving machine tool selection Tool use guidelines: 1 the acrylic cutting processing, recommend using spiral milling, single blade is processing smokeless insipidity, speed, high efficiency, non-sticky, environmental protection, its special real manufacturing process ensure machining the acrylic not and very thin knife (or even no knife), the surface is bright and clean level off. Surface to grind arenaceous effect, recommend using double spiral milling three blade. 2 density board (advertising mold cutting with), recommend using double spiral milling large scraps discharge, it has two high capacity scraps discharge groove, double design, has very good scraps discharge function, and then reach good balance in process, tools, high density board, don't smoke, black hat long service life etc. 3 aluminum cutting, recommend using single blade special-purpose aluminum with www.fmuser.com
第 16 页 共 22 页
cutter. In the process, non-stick knife, speed, high efficiency. 4 precision machining, recommend using small anaglyph round bottom kedao. 5 the cork, density board, original wood, PVC, acrylic large-scale deep anaglyph processing, recommend using single blade spiral milling. 6 no burr below on cutting, recommend using single blade, the double downcutting cutters. 7. Metal sculpture processing, recommend using single blade knife, double straight slot pan. 8.3 D wrecking maze &sealed ring, and a sharp edge, can make accurate 3D sculpture processing. 9 high density board, wood cutter tooth recommended edges. The MLB, plywood, processing, recommend using double straight slot cutter. 11. Slice blade effect, processing products processing, no burr surface will become warped. 12 metal mould machining milling cutter, recommend use tungsten, surface coating with hard titanium tresses. 13. The acrylic mirror sculpture processing recommended wrecking diamond. 14 as early particieboard recommended many stripes cutters. Appendix 2 www.fmuser.com
第 17 页 共 22 页
ARTCAM software interface and basic function is introduced (detailed check discs advanced tutorial lessons) 1 interface,
www.fmuser.com
第 18 页 共 22 页
Vector editing area
Tool.path.parts
www.fmuser.com
第 19 页 共 22 页
Basic processing parameters Settings (such as the depth, specifications, carving speed, spindle speed, etc.)
Note: no, just a specified parameters such as a safe speed, the specific scope when still can control software by adjusting the processing speed or spindle speed Mm diameter to a deep hole of 2mm, for example, materials for 2mm thick PVC board As the chart shows, processing mode selection process, the 2d profiles, 2mm safety depth of machining tool select Z highly 5mm 2mm cutter, from asher 0.5 mm downcutting step is to cut 2mm depth (four) feedrate 15mm/SEC (or 900mm/min) slice rate 6mm/SEC (or 360mm/min) spindle 15,000
Commonly use the default cutting direction along the milling, special circumstances can adopt inverse milling (such as sculpture soft material, such as cork, to improve smoothness, etc.)
Other general can use the default Settings
Choose the right to processing, now click vector sword will automatically generate Finally, save the format selection tool path G Code (mm) tap
www.fmuser.com
第 20 页 共 22 页