扩展电流反馈放大器的可用性

2021-09-24 19:41

晶闸管电源

Texas Instruments IncorporatedAmplifiers: Op Amps

Expanding the usability of current-feedback amplifiers

By Randy Stephens (Email: r-stephens@)

Systems Specialist, Member Group Technical Staff

Introduction

Although current-feedback (CFB) amplifiers have beenaround as long as the widely utilized voltage-feedback (VFB)amplifiers, their acceptance has been sporadic. One of thereasons for this is quite simple—they have a different

name and therefore must be difficult and very hard to use.This is simply not true. There are numerous papers1, 2, 3comparing the differences between the two amplifiertypes that show they are more similar to each other thandifferent. In fact, for numerous circuits, a CFB amplifiermay actually yield better results due to its inherent slew-rate advantage, lack of a gain-bandwidth product, and reasonably low noise for the performance.

Almost every paper written about CFB amplifiers cautionsreaders that placing a capacitor directly in the feedback path,without any resistance in series, will cause the CFB ampli-fier to oscillate. This is true, as the compensation of theamplifier is tied directly to the feedback impedance. Since acapacitor has low impedance at high frequencies, this essen-tiallyplaces a short in the feedback path that inadvertentlydefeats amplifier compensation, resulting in instability.Because of this limitation, there are a handful of commoncircuits that are not recommended for use with a CFBamplifier. These include integrators, some types of filters,and special feedback-compensation techniques. But whatif there was a way to make these circuits work? And whatif the solution was as simple as adding a single component?This would make it feasible to implement a CFB amplifierfor just about every application for which a VFB amplifiercould be used, with the benefits of the CFB amplifier.

Compensation

This article does not explain the compensation theory ofVFB and CFB amplifiers, as there are many papers writtenon this topic. The only thing that is important is thatthere must be resistance, or impedance, in the feedbackpath at the open-loop intersection point to make the CFBamplifier stable.

Figure 1 shows a traditional VFB amplifier, a THS4012,configured in a noninverting gain of +5 with a simple low-pass gain filter set at approximately 1 MHz by the straight-forward 1/(2πRFCF) formula.

If a CFB amplifier like the THS3112 is simply droppedinto this circuit, it willoscillate and the circuit willbecome useless. A method of compensating the CFB

amplifier in this circuit is to insert a resistance, or imped-ance (Z), in the feedback path as shown in Figure 2.It can easily be seen that regardless of the impedance of the feedback path represented by RFand CF, theimpedance Z is in the amplifier’s feedback loop dictatingthe compensation of the amplifier. The interesting thingabout this configuration is that the feedback resistance(RF), which normally dictates the compensation of the

amplifier, can now be essentially any resistance desired.The reader should keep in mind that this is still a high-speed amplifier with speeds over 100 MHz; so the feedbackresistance should always be kept less than a few kilohmsto minimize the effects of parasitic capacitances on theoverall circuit. Conversely, minimizing the resistance toomuch will place too much of a load on the amplifier, typically degrading performance.

One of the drawbacks of adding the impedance Z in thismanner is that the summing node at the inverting terminalis now separated from the virtual summing node. This can

晶闸管电源

Amplifiers: Op Amps

Texas Instruments Incorporated

introduce errors into the system due to

the bias current and the dynamic signalcurrent flowing through this impedance;but these effects are reasonably small as

long as the impedance is minimized.

Adding impedance Z can affect inputoffset voltage due to the dc input biascurrent, which is typically 1 to 10 µA,

multiplied by the impedance Z. Thisresulting voltage gets multiplied by thenoise gain of the circuit. Additionally, whena signal appears at the output, the CFBamplifier (as the name implies) relies on

an error current flowing through theinvertingnode through the impedance Z,producing a signal error. However, sincethe transimpedance of most CFB ampli-fiers is well over 100 k and sometimes ashigh as several megohms, this error is also

minimized if the impedance is kept low. The

drift of this circuit now also relies on the

temperature characteristics of impedance

Z and should not be used as a precisionamplifier; but most CFB amplifiers are notused as precision amplifiers anyway due to

stated previously. This shows that there is a reasonably widetheir inherent topology limitations. Overall, these issues

range of acceptable values for Z and does not imply that theare minimal and, for most systems, can be effectively

selection for Z is highly critical. Figure 3 also illustrates aignored in favor of the CFB amplifier’s advantages as

扩展电流反馈放大器的可用性.doc 将本文的Word文档下载到电脑 下载失败或者文档不完整,请联系客服人员解决!

下一篇:高中英语 河南洛阳市汝阳一高高三年级上学期一轮复习之动词不定

相关阅读
本类排行
× 注册会员免费下载(下载后可以自由复制和排版)

马上注册会员

注:下载文档有可能“只有目录或者内容不全”等情况,请下载之前注意辨别,如果您已付费且无法下载或内容有问题,请联系我们协助你处理。
微信: QQ: