扩展电流反馈放大器的可用性(2)

2021-09-24 19:41

common trait for current-feedback amplifiers—as the feed-previously stated.

backimpedance is decreased, the peaking will increase. If

Testing with different Z valuesthe impedance is too low, there is a good chance that theThe easiest way to see if the circuit is stable is to use acircuit will become unstable and oscillate, as illustrated bynetwork analyzer frequency sweep. Instability can typical-the response when Z = 200 .

ly be seen as sharp rises in the frequency response at the

Output noiseamplifier’s bandwidth limitations. If the peaking is smooth,

One element that may be very important in a system is theor there is no peak, then the amplifier should be stable.

output noise. Adding a resistance in the manner discussedFigure 3 shows the frequency response of the system with

only makes the output noise worse. The inverting currentdifferent values of resistors for the variable Z.

noise of the amplifier goes through the resistance at Z andThe response of the THS4012 is also shown for reference

creates a voltage noise. This noise then becomes multipliedto easily compare the performance of the two systems. It

by the circuit’s gain, which is frequency-dependent.is interesting that no matter what resistance is used for Z,

For a CFB amplifier, the inverting current noise is typi-the responses below 20 MHz look identical to each other.

cally the highest noise component of the amplifier. AlthoughThis is the ultimate goal of this configuration—no differ-the CFB amplifier voltage noise is inherently very low, ences in signal performance. For the stability part of the

——

typically less than 3 nV/√Hz, the inverting currentnoise ofcircuit, the area above 20 MHz must be examined.

——

most CFB amplifiers is generally around 15 to 20 pA/√Hz.Examining the circuits in Figures 1 and 2 shows us that

The noninverting current noise is only noticeable if thethe feedback impedance is dictated by the capacitor CF.

source impedance is high. Using a 50- environment Above 20 MHz, this impedance is very small—essentially

minimizes the noninverting current noise.creating a short from the output to the summing node. This

The THS3112 was designed to have very low noise. Theconfiguration is commonly referred to as a unity buffer with

——4voltage noise is 2.2 nV/√Hz, the noninverting current noisethe signal gain set to 1. The data sheet for the THS3112

——

is 2.9 pA/√Hz, and the critical inverting current noise is arecommends that, in a gain of +1 under the circuit condi-——

low 10.8 pA/√Hz. However, multiplying the inverting currenttions utilized, the feedback resistance be 1 k . Thus, it is

noise by 1 k and then multiplying by the gain can aloneno surprise to see that when Z = 1 k , the response looks

——

produce a very substantial output noise of about 54 nV/√Hzvery smooth and well behaved, indicating a very stable

in the pass band. To quantify the output noise of the system,system. However, when Z = 681 , the response also looks

the circuits shown in Figures 1 and 2 were tested for outputvery reasonable and helps minimize the potential issues

晶闸管电源

Texas Instruments IncorporatedAmplifiers: Op Amps

noise (see Figure 4). For comparison, the THS4012, with a

——

respectable voltage noise of 7.5 nV/√Hzand both current

——

noises of 1 pA/√Hz, is also shown in Figure 4.

Note that the output noise of the THS4012 is the sameas when using the THS3112 with Z = 475 . Again, theseresponses are just like those of a VFB amplifier in the tradi-tionalconfiguration, showing that the basic functionality issound—thereare no differences between a VFB amplifierand this configuration. Figure 4 shows that although usingZ = 1 k produces a very stable amplifier, the output

——

noise is 20 nV/√Hzhigher than that of the THS4012.

Keep in mind that the THS3112 has very low overallnoise but that many other CFB amplifiers will probablyproduce much higher noise. The only way to get aroundthis is if the unity-gain stability of the amplifier requires avery small resistor of, say, only 500 or less. But what ifthere was another way to make the CFB amplifier stableandhave low noise at the same time?

Fundamentally speaking, the circuit needs high impedancewithin the feedback path only at the amplifier’s bandwidthlimit. At frequencies below this point, it really does notmatter what the impedance is, and the amplifier will work

fine. The issues stated previously are alsominimized, resulting in an even bettersystem than one using pure resistors.The first solution that comes to mind isto use an inductor. Inductors have lowimpedance at low frequencies and highimpedance at high frequencies—exactlywhat is desired; but their relatively largesize and high cost are generally consideredprohibitive. An alternative componentthat minimizes these disadvantages andstill functions the same is the ferrite chip.

扩展电流反馈放大器的可用性(2).doc 将本文的Word文档下载到电脑 下载失败或者文档不完整,请联系客服人员解决!

下一篇:高中英语 河南洛阳市汝阳一高高三年级上学期一轮复习之动词不定

相关阅读
本类排行
× 注册会员免费下载(下载后可以自由复制和排版)

马上注册会员

注:下载文档有可能“只有目录或者内容不全”等情况,请下载之前注意辨别,如果您已付费且无法下载或内容有问题,请联系我们协助你处理。
微信: QQ: