As expected, the responses all look comparable to eachother below 10 MHz. Additionally, the resistance valuesaffect the stability and again show that the higher theresistance is, the better the stability. Using a resistance aslow as 475 actually shows respectable performance in thisconfiguration. Remember that for oscillations to occur, thegain must be above unity gain, or 0 dB. As long as the peakis below 0 dB, oscillations should not occur. As in the non-inverting case, using 200 shows a large narrow peak thatwill most likely result in stability issues and/or oscillations.However, notice that above 10 MHz the same generalshape occurs for both the CFB and VFB amplifiers. This iscaused by the amplifiers’ input and output impedancesbecoming very high above their bandwidth limit. Whenthis occurs, there is a path for the input signal to flowthrough RG, through CF, and then to feed forward to theload. Of course, the amplifiers’ own input and output
capacitances also affect the amount of feed-through in thecircuit; but it is important to remember that this occursabove the amplifiers’ usable bandwidths.
Just as for the noninverting configuration, using ferritechips has several advantages for the inverting configuration.
晶闸管电源
Amplifiers: Op Amps
Texas Instruments Incorporated
Figure 11 shows the frequency responsesof several of these chips. Figure 12 showsthe results of using various ferrite chipsfrom the same AG family.
As expected, all of these graphs showthe same type of results obtained withthe noninverting configuration. Using alow-Q ferrite chip with high impedancewill result in a stable system. Although thenoise plots for this configuration are notpresented here, they will show the sametype of results as the noninverting configu-ration; using ferrite chips will have thelowest output noise of any configuration.
Conclusion
Although this article shows only two con-figurations with capacitors in the feedbackpath, it shows the fundamental feasibilityof this compensation technique. Whileresistors do work very well, producing themost stable responses, the drawbacks ofthe output noise coupled with the dc andac errors may limit some of the ing ferrite chips helps alleviate manyof these issues, producing the lowest noiseof all with no dc errors or in-band ac sig-nal errors; and stability is almost as goodas when utilizing resistors. It is importantto choose the proper ferrite chip with theamplifier; but this is considered normalprocedure for any circuit design and is nomore difficult than selecting the rightamplifier for the system.
This simple technique helps eliminateone of the major drawbacks of using theCFB amplifier while allowing any systemto enjoy many of its benefits. Designers ofmultiple feedback filters, for example, oncelimited to the use of VFB amplifiers, cannow take advantage of the superior slewrates and lack of gain-bandwidth productcharacteristics found in the CFB amplifier.
References
For more information related to this article,you can downloadan Acrobat Reader fileat /sc/techlit/litnumberandreplace “litnumber”with the TI Lit. #for the materials listed below.
Document TitleTI Lit. #1.“Voltage Feedback Vs. Current Feedback
Op Amps,” Application Report . . . . . . . . . . . . . .slva0512.“The Current-Feedback Op Amp: A High-Speed Building Block,” Application Bulletin . . .sboa0763.“Current Feedback Amplifiers: Review, Stability Analysis, and Applications,”
Application Bulletin . . . . . . . . . . . . . . . . . . . . . . .sboa0814.“Low-Noise, High-Speed Current Feedback
Amplifiers,” Data Sheet . . . . . . . . . . . . . . . . . . . .slos3855.“Effect of Parasitic Capacitance in Op Amp
Circuits,” Application Report . . . . . . . . . . . . . . .sloa013
Related Web sites
/sc/device/partnumber
Replace partnumberwith OPA685, THS3112, THS3202orTHS4012
晶闸管电源
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reservethe right to make corrections, modifications, enhancements,improvements, and other changes to its products and services atany time and to discontinue any product or service without notice.Customers should obtain the latest relevant information beforeplacing orders and should verify that such information is currentand complete. All products are sold subject to TI's terms andconditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to thespecifications applicable at the time of sale in accordance with TI'sstandard warranty. Testing and other quality control techniques areused to the extent TI deems necessary to support this warranty.Except where mandated by government requirements, testing ofall parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customerproduct design. Customers are responsible for their products andapplications using TI components. To minimize the risksassociated with customer products and applications, customersshould provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express orimplied, is granted under any TI patent right, copyright, mask workright, or other TI intellectual property right relating to anycombination, machine, or process in which TI products or servicesare used. Information published by TI regarding third-partyproducts or services does not constitute a license from TI to usesuch products or services or a warranty or endorsement e of such information may require a license from a third partyunder the patents or other intellectual property of the third party, or alicense from TI under the patents or other intellectual property of TI.Reproduction of information in TI data books or data sheets ispermissible only if reproduction is without alteration and isaccompanied by all associated warranties, conditions, limitations,and notices. Reproduction of this information with alteration is anunfair and deceptive business practice. TI is not responsible orliable for such altered documentation.