verification of the effective depth of carburizod and hardened cases of steel parts
76 GB/T 9451-1988 钢件薄表面总硬化层深度或有效硬化层深度的测定 Determination of total or effective thickness of thin surface hardened layers of steel parts
77 GB/T 9452-1988 热处理炉有效加热区测定方法 Testing method for working zone of heat treating furnace
78 GB/T 9460-1988 铜及铜合金焊丝 Welding wire and rods of copper and copper alloys 79 GB/T 10044-1988 铸铁焊条及焊丝 Covered electrodes and welding rods for welding cast iron
80 GB/T 10045-1988 碳钢药芯焊丝 Carbon steel flux cored wires for arc welding 81 GB/T 10046-1988 银基钎料 Silver brazing filler metals
82 GB/T 10858-1989 铝及铝合金焊丝 Aluminium and aluminium alloy welding rods and wires 83 GB/T 10859-1989 镍基钎料 Nickel base brazing filler metals
84 GB/T 11350-1989 铸件机械加工余量 Machining allowances on castings 85 GB/T 11351-1989 铸件重量公差 Mass tolerances for castings
86 GB/T 11352-1989 一般工程用铸造碳钢件 Carbon steel castings for general engineering purposes
87 GB/T 11354-1989 钢铁零件 渗氮层深度测定和金相组织检验 Steel-iron parts—
Determination of nitrided case depth and metallographic examination of nitriding structure 88 GB/T 11363-1989 钎焊接头强度试验方法 Methods of the strength tests for brazed and soldered joint
89 GB/T 11364-1989 钎料铺展性及填缝性试验方法 Test method of spreadability and clearance filling ability for filler metal
90 GB/T 12214-1990 熔模铸造用硅砂、粉 Silica sand and flour for investment casting
91 GB/T 12215-1990 熔模铸造用铝矾土砂、粉 Bauxite sand and flour for investment casting 92 GB/T 12216-1990 铸造用合脂粘结剂 The residue from distillation of synthetic fatty acids as binder for foundry
93 GB/T 12361-1990 钢质模锻件 通用技术条件 General specification of steel die forgings 94 GB/T 12362-1990 钢质模锻件 公差及机械加工余量 Tolerances and machining allowances of steel die forgings
95 GB/T 12363-1990 锻件功能分类 Classification of forging functions
96 GB/T 12469-1990 焊接质量保证 钢熔化焊接头的要求和缺陷分级 Quality assurance of welding—Requirement for fusion welding joint of steel and classification for imperfection
97 GB/T 12470-1990 低合金钢埋弧焊用焊剂 Fluxes for the submerged arc welding of low alloy steel
98 GB/T 12603-1990 金属热处理工艺分类及代号 Classification and designation on metal heat treatment
99 GB 12935-1991 焊条烘干炉运行能耗标准 Energy consumption standard in operation of covered electrode furnace
100 GB/T 13311-1991 锅炉受压元件焊接接头机械性能试验方法 Boiler pressure parts—Mechanical test for welded joints
101 GB/T 13320-1991 钢质模锻件 金相组织评级图及评定方法 Metallographic grading atlas and assessing method for steel die forgings
102 GB/T 13450-1992 对接焊接头宽板拉伸试验方法 Method of wide plate tension test for butt welded joint
俊业翻译 26 103 GB/T 13679-1992 锰基钎料 Manganese base brazing filler metals
104 GB/T 13814-1992 镍及镍合金焊条 Nickel and nickel alloy covered welding electrodes 105 GB/T 13815-1992 铝基钎料 Aluminium base brazing filler metals
106 GB/T 13816-1992 焊接接头脉动拉伸疲劳试验方法 Test method for pulsed tensile fatigue of welded joints
107 GB/T 13817-1992 对接接头刚性拘束焊接裂纹试验方法 Method of rigid restraint cracking test for welding butt joint
108 GB/T 13818-1992 压铸锌合金 Zinc die-casting alloys 109 GB/T 13819-1992 铜合金铸件 Copper alloy castings 110 GB/T 13820-1992 镁合金铸件 Magnesium alloy castings 111 GB/T 13821-1992 锌合金压铸件 Zinc alloy die castings
112 GB/T 13822-1992 压铸有色合金试样 Test specimens for non ferrous diecasting alloys 113 GB/T 13914-1992 冲压件尺寸公差 Tolerance of dimensions for stampings 114 GB/T 13915-1992 冲压件角度公差 Tolerance of angles for stampings
115 GB/T 13916-1992 冲压件形状和位置未注公差 Unnoted tolerance of shape and position for stampings
116 GB/T 13925-1992 铸造高锰钢金相 Metallographs for high manganese cast steel
117 GB/T 14235.1-1993 熔模铸造模料 熔点测定方法(冷却曲线法) Testing method for melting point of pattern materials in investment casting
118 GB/T 14235.2-1993 熔模铸造模料 抗弯强度测定方法 Testing method for bending strength of pattern materials in investment casting
119 GB/T 14235.3-1993 熔模铸造模料 灰分测定方法 Testing method for ash content of pattern materials in investment casting
120 GB/T 14235.4-1993 熔模铸造模料 线收缩率测定方法 Testing method for linear contraction of pattern materials in investment casting
121 GB/T 14235.5-1993 熔模铸造模料 表面硬度测定方法 Testing method for surface hardness of pattern materials in investment casting
122 GB/T 14235.6-1993 熔模铸造模料 酸值测定方法 Testing method for acid number of pattern materials in investment casting
123 GB/T 14235.7-1993 熔模铸造模料 流动性测定方法 Testing method for fluidity of pattern materials in investment casting
124 GB/T 14235.8-1993 熔模铸造模料 粘度测定方法 Testing method for viscosity of pattern materials in investment casting
125 GB/T 14235.9-1993 熔模铸造模料 热稳定性测定方法 Testing method for thermal stability of pattern materials in investment casting
126 GB/T 14408-1993 一般工程与结构用低合金铸钢件 Low alloy steel castings for general engineering and structural purposes
127 GB/T 15055-1994 冲压件未注公差尺寸极限偏差 Permissible stamping varitions in dimensions without tolerance indication
128 GB/T 15056-1994 铸造表面粗糙度 评定方法 Evaluation method on cast surface roughness
129 GB/T 15111-1994 点焊接头剪切拉伸疲劳试验方法 Test method for shear tensile fatigue of spot welded joints
130 GB/T 15114-1994 铝合金压铸件 Aluminium alloy die-castings
俊业翻译 27 131 GB/T 15115-1994 压铸铝合金 Die casting aluminium alloys 132 GB/T 15116-1994 压铸铜合金 Die casting copper alloys 133 GB/T 15117-1994 铜合金压铸件 Copper alloy die castings
134 GB/T 15169-1994 钢熔化焊手焊工资格考核方法 Approval testing of manual welders--Fusion welding-steel
135 GB/T 15620-1995 镍及镍合金焊丝 Nickel and nickel alloy welding wires
136 GB 15735-1995 金属热处理生产过程安全卫生要求 Requirements for the safety and health in production process of metal heat treatment
137 GB/T 15747-1995 正面角焊缝接头拉伸试验方法 Method of tension test for front fillet welded joint
138 GB/T 15825.1-1995 金属薄板成形性能与试验方法 成形性能和指标 Sheet metal formability and test methods--Formability and indexes
139 GB/T 15825.2-1995 金属薄板成形性能与试验方法 通用试验规程 Sheet metal formability and test methods--General test rules
140 GB/T 15825.3-1995 金属薄板成形性能与试验方法 拉深与拉深载荷试验 Sheet metal formability and test methods--Drawing and drawing load test
141 GB/T 15825.4-1995 金属薄板成形性能和试验方法 扩孔试验 Sheet metal formability and test methods--Hole expanding test
142 GB/T 15825.5-1995 金属薄板成形性能与试验方法 弯曲试验 Sheet metal formability and test methods--Bending test
143 GB/T 15825.6-1995 金属薄板成形性能与试验方法 锥杯试验 Sheet metal formability and test methods--Conical cup test
144 GB/T 15825.7-1995 金属薄板成形性能与试验方法 凸耳试验 Sheet metal formability and test methods--Earing test
145 GB/T 15825.8-1995 金属薄板成形性能与试验方法 成形极限图(FLD)试验 Sheet metal formability and test methods--Forming limit diagram (FLD) test
146 GB/T 15826.1-1995 锤上钢质自由锻件机械加工余量与公差一般要求 Machining allowances and tolerances for steel open die forgings on hammer--General reguirement 147 GB/T 15826.2-1995 锤上钢质自由锻件机械加工余量与公差盘、柱类 Machining allowances and tolerances for steel open die forgings on hammer--Disks and columns 148 GB/T 15826.3-1995 锤上钢质自由锻件机械加工余量与公差 带孔圆盘类 Machining allowances and tolerances for steel open die forgings on hammer--Disk swith holes
149 GB/T 15826.4-1995 锤上钢质自由锻件机械加工余量与公差 圆环类 Machining allowances and tolerances for steel open die forgings on hammer--Rings
150 GB/T 15826.5-1995 锤上钢质自由锻件机械加工余量与公差 套筒类 Machining
allowances and tolerances for steel open die forgings on hammer--Seamles cylinder hushings 151 GB/T 15826.6-1995 锤上钢质自由锻件机械加工余量与公差 光轴类 Machining allowances and tolerances for steel open die forgings on hammer--Shaft without steps 152 GB/T 15826.7-1995 锤上钢质自由锻件机械加工余量与公差 台阶轴类 Machining allowances and tolerances for steel open die forgings on hammer--Shaft with steps
153 GB/T 15826.8-1995 锤上钢质自由锻件机械加工余量与公差 单拐曲轴类 Machining allowances and tolerances for steel open dle forgings on hammer--Single throw crankshaft 154 GB/T 15826.9-1995 锤上钢质自由锻件机械加工余量与公差 黑皮锻件 Machining allowances and tolerances for steel open die forgings on hammer--Forging without machining
俊业翻译 28 155 GB/T 15829.1-1995 软钎焊用钎剂 分类、标记与包装 Soldering fluxes--Classification, labelling and packaging
156 GB/T 15829.2-1995 软钎焊用钎剂 树脂类钎剂 Soldering fluxes--Resin basis fluxes 157 GB/T 15829.3-1995 软钎焊用钎剂 有机物类钎剂 Soldering fluxes--Organic fluxes 158 GB/T 15829.4-1995 软钎焊用钎剂 无机物类钎剂 Soldering fluxes--Inorganic fluxes 159 GB/T 16253-1996 承压钢铸件 Steel castings for pressure purposes 160 GB/T 16672-1996 焊缝 工作位置 倾角和转角的定义 Welds--Working positions--Definitions of angles of slope and rotation
161 GB/T 8541-1997 锻压术语 Terminolgy of forging and stamping 162 GB/T 16743-1997 冲裁间隙 Blanking clearance 163 GB/T 16746-1997 锌合金铸件 Zinc alloy castings 164 GB/T 1175-1997 铸造锌合金 Casting zinc alloys
165 GB/T 16923-1997 钢件的正火与退火 Normalizing and annealing of steel parts 166 GB/T 16924-1997 钢件的淬火与回火 Quenching and tempering of steel parts
167 GB/T 16957-1997 复合钢板焊接接头力学性能试验方法 Mechanical tests on welded joints in clad plates
168 GB/T 6060.1-1997 表面粗糙度比较样块 铸造表面 Roughness comparison specimens Cast surfaces
169 GB/T 5611-1998 铸造术语 Foundry terminology
170 GB/T 5680-1998 高锰钢铸件 Austenitic manganese steel castings 171 GB/T 9442-1998 铸造用硅砂 Foundry silica sand 172 GB/T 17445-1998 铸造磨球 Cast grinding balls
173 GB/T 12467.1-1998 焊接质量要求 金属材料的熔化焊 第一部分: 选择及使用指南 Quality requirements for welding--Fusion welding of metallic materials--Part 1: Guidelines for selection and use
174 GB/T 12467.2-1998 焊接质量要求 金属材料的熔化焊 第二部分: 完整质量要求 Quality requirements for welding--Fusion welding of metallic materials--Part 2: Comprehensive quality requirements
175 GB/T 12467.3-1998 焊接质量要求 金属材料的熔化焊 第三部分: 一般质量要求 Quality requirements for welding--Fusion welding of metallic materials--Part 3: Standards quality requirements
176 GB/T 12467.4-1998 焊接质量要求 金属材料的熔化焊 第四部分: 基本质量要求 Quality requirements for welding--Fusion welding of metallic materials--Part 4: Elementary quality requirements
177 GB/T 17493-1998 低合金钢药芯焊丝 Low alloy steel flux cored electrodes for arc welding 行业标准规范英汉对照-通用机械
241 GB/T 13756-1992三足式离心机型式和基本参数Three-column centrifuge--Types and basic parameters
242 GB/T 13928-1992微型往复活塞空气压缩机Reciprocating piston micro air compressor 243 GB/T 13929-1992水环真空泵和水环压缩机试验方法Methods of testing for water-ring vacuum pumps and compressors
244 GB/T 13930-1992水环真空泵和水环压缩机气量测定方法Methods for the measurement of volume flow of gas of water-ring vacuum pump and compressor 245 GB/T 13931-1992电除尘器
俊业翻译 29 性能测试方法Methods of performance tests for electrostatic precipitators 246 GB/T 13933-1992小型贯流式通风机Miniature cross-flow fan 247 GB/T 14173-1993平面钢闸门
技术条件Specification for hydraulic flat steel gates
248 GB 14193-1993液化气体气瓶充装规定Rules for filling of liquefied gas cylinders 249 GB 14194-1993永久气体气瓶充装规定Rules for filling of permanent gas cylinders 250 GB/T 14405-1993通用桥式起重机General purpose overhead cranes 251 GB/T 14406-1993通用门式起重机General purpose gantry cranes 252 GB/T 14407-1993通用桥式和门式起重机司机室
技术条件Specification for cabins of overhead travelling cranes and portal bridge cranes for general purposes
253 GB/T 14521.1-1993运输机械术语
运输机械类型Terms of conveying machinery--Types of conveying machinery 254 GB/T 14521.2-1993运输机械术语
主要参数Terms of conveying machinery--Main parameters 255 GB/T 14521.3-1993运输机械术语
装置和零部件Terms of conveying machinery--Unit and component parts 256 GB/T 14521.4-1993运输机械术语
带式输送机Terms of conveying machinery--Belt conveyor 257 GB/T 14521.5-1993运输机械术语
埋刮板输送机Terms of conveying machinery--En masse conveyor 258 GB/T 14521.6-1993运输机械术语
板式输送机Terms of conveying machinery--Slat conveyor 259 GB/T 14521.7-1993运输机械术语
螺旋输送机Terms of conveying machinery--Screw conveyor 260 GB/T 14521.8-1993运输机械术语
流体输送机Terms of conveying machinery--Fluid conveyor 261 GB/T 14521.9-1993运输机械术语
提升机Terms of conveying machinery--Elevator
262 GB/T 14566-1993正拱形金属爆破片型式与参数Specification and type for conventional domed metallic bursting discs
263 GB/T 14567-1993反拱形金属爆破片型式与参数Specification and type for reverse domed metallic bursting discs
264 GB/T 14568-1993开缝形金属爆破片型式与参数Specification and type for slotted metallic bursting discs
265 GB/T 14627-1993大型液压式启闭机Heavy hydraulic hoister
266 GB/T 14784-1993带式输送机安全规范Safety regulations of belt conveyor 267 GB/T 14794-1993蒸汽往复泵Steam reciprocating pump 268 GB/T 14811-1993热管术语Heat pipe terminology
269 GB/T 14812-1993重力热管传热性能试验方法The testing method of heat transfer performance for gravity heat pipe
270 GB/T 14813-1993热管寿命试验方法Life testing method for heat pipe 271 GB/T 15186-1994分离机
型式与基本参数Separator--Types and basic parameters
俊业翻译 30