Fault code (2012 Feb) Updated KDL16 _0126
0107 子代码 称重故障 电梯启动时称重设备给出错误的值。(电压少于0.6V) 数据1 0 数据2 0 原因 侦查 调整称重装置。 恢复 断开LWD Perform LWD setup. 测试 load initial settings 1041 1042 子代码名称 LWD输入变化太小 称重没有设置 描述 不能调节或丢失 LWD setup missing. 2008 称重 称重传感器信号超出范围或未设置LWD 0 0 3020 称重警告 LWD设置错误或超载 0 0 动作 当LWD工作正禁止再起动 常时 LWD setup is not made HCB is Inspection checking that and shaft LWD setup is setup is done. possible 传感器损坏，布线错误驱动测量感应驱动无法动作 或未设置LWD 电流，数值太高或太低，监控失效。未设置LWD禁止进行纠正 LWD设置错误或未设置基于现有的设正常运行但运或传感器位置错误 置，计算载行后出现警告重。若数值太显示 高或太低，出现警示界面 测速电压不跟随速度参考值。 电梯急停，不会再启动。 侦查 驱动比较参考速度及马达速度。若差值较大，监控失效 当故障排除。 当信号处于适当断开LWD 的范围或LWD已设定，自动恢复 当计算的载重处于适当的范围或LWD已设定，自动恢复 设置错误的LWD值 0108 Tacho故障 Tacho 极性接反；轿厢与对重平衡不良；称重不准；制动器没打开；驱动参数不正确；超速。 数据1 位置（cm） 数据2 速度＋模态（cm/s）+最后数的模式 拆去测速线。 子代码 2009 子代码名称 速度差异 描述 参考速度与测量的速度不同 原因 前馈力矩不协调，极限太低，速度控制不协调，马达速度回应或系统参数有问题 动作 急停 恢复 自动恢复 测试 力矩极限参数设为最低值 21 - 95
Fault code (2012 Feb) Updated KDL16 _0126
2010 速度参考故障 Velocity reference is over its supervision limit. 0 0 Wrong system parametrization. 2011 针对V3F16 Stalling protection Motor does not rotate, check brake operation. Wrong parametrization. Error in tachometer wiring. TACHO adjustment wrong 编程器损坏，编程器连线或系统参数错误 2012 速度反馈饱和 Too high voltage in tachometer input 0 0 2013 DTC (双TACHO控制) 超出测速计的范围 位置（cm） 速度＋模态（cm/s）+最后数的模式 2069 速度扭矩控制监控计算故障 超出速度调节力矩范围 位置（cm） 速度＋模态（cm/s）+前溃参数或LWD不能调节或马达需要额外的力HCB supervising that calculated speed reference has to be below parameter value limit. By comparing measured value to the reference HCB check that tachometer input voltage is not over the max. limit 驱动比较马达编程器速度。若差值较大，监控失效。测速机故障计算增加（除非处于检查驱动模式） Emergency stop. Automatically Stops immediately Emergency stop. Automatically 急停或失楼层 自动恢复 断开马达编程器或设置错误的脉冲值 立即停止，故障次数增加， 使用错误的系统参数 22 - 95
Fault code (2012 Feb) Updated KDL16 _0126
3001 针对 V3F16 3002 针对 V3F16 3003 DTC 警告 (双TACHO控制) Difference between speed reference and measured speed is at warning limit Needed torque very near of expected Difference limit between speed feedbacks exceeded. 最后数的模式 矩 Difference between speed reference and measured speed 90% of the trip limit By comparing measured value to the reference 3次后锁死 Alarm shown after run Needed torque is 90% of maximum expected Car/motor encoder broken, problem with encoder cables or wrong system parametrization. Alarm shown after run Warning displayed. 3004A 扭力限制警示 输出的速度调节器受限 速度调节力矩接近极限（90％） 输出电压受限 0 0 力矩极限值低或系统参数错误 前溃参数或LWD不能调节或马达需要额外的力矩 网络电压供应低或系统参数错误 3056 DCBH compares speed feedback signals from motor and car encoders and if difference is too big between warning is given. 驱动监控控制输出，若饱和，监控失效 Automatically when speed difference is small enough. 警示 自动恢复 力矩极限参数设为最低值 3062 电压输出警示 0 0 驱动监控控制输出，若饱和，监控失效 警示 自动恢复 降低网络电压供给 23 - 95
Fault code (2012 Feb) Updated KDL16 _0126
0109 位置丢失 驱动丢失位置。 Drive count differs more than 300 mm at 30 or B30 vane edge 原因 Broken/malfunctioning 77 switch or problem with switch cabling. 同步运行。 检查77U/N和61U/N磁铁。 动作 Drive is faulted. 关电后移动电梯。 子代码 1012 子代码名称 描述 77:U/N 开关故障 77:U/N active at the same time. 数据1 0 数据2 0 1013 没有77U/N时77S 动作 77 开关太接近端站 77S active without 77U or 77N 77S active without 77U or 77N Warning that 77 switch position should be adjusted 侦查 77 switch information is monitored and if both 77:U and 77:N are active at the same time. 77S active without 77U or 77N 77 switch edge is compared to the internal positioning 77 switch edge is compared to the internal positioning Locks the elevator Warning only. 恢复 Automatically when switch information is correct or by user: switch to RDF/inspection mode Power reset 测试 Set both 77 switches on at the same time. 2049 2050 Supervisions 0 are active only when 6_98 parameter has value 2 (NA 0.75m/sec) 77开关太远端站 Supervisions 0 are active only when 6_98 parameter has value 2 (NA 0.75m/sec) 0 Automatically Give 77 switch at wrong place 0 Warning that 77 switch position should be adjusted Warning only. Automatically Give 77 switch at wrong place 24 - 95
Fault code (2012 Feb) Updated KDL16 _0126
2051 Ramp slow down 61 or 77 falling edge （北美NA） Ramp slowdown from wrong 77 rising edge （北美NA） 2052 Supervisions 0 are active only when 6_98 parameter has value 2 (NA 0.75m/sec) Supervisions 0 are active only when 6_98 parameter has value 2 (NA 0.75m/sec) Supervisions 0 are active only when 6_98 parameter has value 2 (NA 0.75m/sec) Supervisions 0 are active only when 6_98 parameter has value 2 (NA 0.75m/sec) 位置丢失，需同楼层 步运行 0 Switch has caused too large position position error which caused slowdown 0 77 signal is working at wrong place/time 2060 Quick stop by from 61 edge （北美NA） 0 Switch is missing or large position error 2061 Quick stop by NTS 77 （北美NA） 0 Switch is missing or large position error 3005 轿厢位置 0 61/77信号有误，马达编程器损坏，编程器连线损坏，系统参数错误 switch edge is compared to the stored position and position counter signal edge is compared to the setup table and internal position counting switch edge is compared to the stored position and position counter switch edge is compared to the stored position and position counter 不同的角度计算位置信息，如差距较大，失楼层 Warning only. Automatically Give switch at wrong place Warning only. Automatically Give 77 switch at wrong place Stops immediately Automatically Give switch at wrong place Stops immediately Automatically Give switch at wrong place 停止后警示 位置信息一致和证实当前位置后自动恢复 将77U/N开关设置在井道中央 25 - 95