Fault code (2012 Feb) Updated KDL16 _0126
3016 错误楼层编码警告 NTS停止警告 3017 3053 from floor. Wrong floor code received from floor. Drive has performed NTS stop. Problem with HIPO-M system. 电梯停在某一个61的隔磁片处，77:S和77:U/N是“ON”但楼层位 置不在顶楼/底楼 位置丢失，进行同同步运行之后 步运行 3060 NTS开关位置 检测到的NTS开关与设置不匹配 位置（cm） 速度（cm/s） Problem with car/motor encoder, bad NTS setup or wrong system parametrization. 编程器故障，NTS设置错误，NTS开关或系统参数错误 3061 NTS开关顺序 NTS开关顺序错误 位置（cm） 速度（cm/s） NTS开关故障 77U 77U:1, 77U:2, 77U:3, 77U:4 77N 77N:1, 77N:2, 77N:3, 77N:4 SD卡损坏，清空或文件不正确。 NTS功能将检测到的开关位置与保存的位置相比较，若差距较大，监控失效。 NTS功能监控开关以正常的次序显示，万一顺序有误，监控失效 当SD卡插入读卡器后驱动识别SD卡。 停在下一楼层 自动恢复 移动NTS开关 停在下一楼层 自动恢复 交换NTS开关 3064 SD 卡错误 驱动无法读出SD卡。 3068 坡道减速正当通信监查 Ramp slowdown Communication link to the LCECPU 2=文件丢0 失 3=检查和4=SD 卡类型 position speed+mode [cm] [cm/s] + last SD卡不能用自动 于软件升级。 插入空SD卡。 Disturbance, grounding error, broken wire, control Communication Ramp stop to Automatic link is next floor checked if main Cause disturbance to the 36 - 95
Fault code (2012 Feb) Updated KDL16 _0126
3071 due communication supervision 主驱动马达学习警告 has failed for moment Drive learning needed for Master unit. number is mode system failure 3072 次驱动马达学习警告 Drive learning needed for Follower unit. Difference between motor source voltage parameter and measured value is too high or ABB ID Run Done status is FALSE. Difference between motor source voltage parameter and measured value is too high or ABB ID Run Done status is FALSE. continuously, contactor timeout is stays on. 500ms communication link 0125
力矩超极限
负载过大；平衡不对；轿厢 尺寸、马达型号可能会错。
电梯急停，不会再启动。
检查参数和 马达电源。
0126 安全继电器开路 检查XSR1的连接和控制板。 数据2 0 电梯急停，不会再启动。 原因 抱闸或抱闸控制模块问题 侦查 当有较多连续的126_3059故障警示时，产生此问题 当有较多连续的126_2071 子代码 子代码名称 1045A 抱闸电流的折算电压 描述 数据1 检测到的折算电0 压电流多次失效 动作 驱动故障 恢复 测试 检修/RDF模式 - 1046 抱闸自动检测 抱闸自动检测多次失败 0 0 抱闸问题 驱动故障 检修/RDF模式 - 37 - 95
Fault code (2012 Feb) Updated KDL16 _0126
1047 抱闸电流 无抱闸电流 0 0 1058 No feedback from brake Control 抱闸控制没有反馈 No communication from BCX to DCBL for too long. 0 0 或126_2072故障警示时，产生此问题 抱闸或抱闸控制模块当有较多连续驱动故障 问题 的126_2104故障警示，产生此问题 Problem with brake This fault 驱动故障 cable or with brake occurs when module. BCX feedback is missing for too long. 检修/RDF模式 断开抱闸连线，试图运行 1059 Brake control does not receive reference messages 抱闸控制没有接收到参考信息 No correct reference messages from DCBL to BCX for too long. 0 0 Problem with brake This fault cable or with brake occurs when module. BCX is not receiven a correct message for too long. 驱动故障 检修/RDF模式 Drive the elevator, wait at least 3 seconds and disconnect current feedback from XB1. Elevator should run at least 21 seconds for the fault to occur. 检修/RDF模式 Drive the elevator, wait at least 3 seconds, create disturbance on voltage reduction 38 - 95
Fault code (2012 Feb) Updated KDL16 _0126
1060 Brake controller failed 抱闸控制模块失效 BCX brake control board has communicated hardware failures too many times. BCX fault code: 1 = +24V supply is below 14V 2 = Relay\\Relays are stuck 4 = Short circuit in output 8 = Brake control signal stuck high 16 = Coil leaks to ground 32 = Too low 0 Problem with BCX brake controller This fault occurs if there's too many consecutive 126_3075 faults. 驱动故障 signal in XB1 so that message cannot be correctly received from BCX. Elevator should run at least 21seconds for the fault to occur. 检修/RDF模式 Arrange one BCX specific harware failure 39 - 95
Fault code (2012 Feb) Updated KDL16 _0126
2071A 抱闸测试失败：速度 检测马达速度 brake current 64 = CRC16/RAM Test/Register failed 128 = Brake signal possibly stuck low 256 = Drive enable signal is stuck (code is sum of previous in case of multiple faults) 0 0 抱闸问题 2072A 抱闸测试失败：位置 检测轿厢的运行 0 0 抱闸问题 2104 抱闸电流 抱闸打开时未检测到抱闸电流 0 0 抱闸或抱闸控制模块问题 自动抱闸检测时，驱动控制速度。此监控只有在抱闸自动检测时财有效 自动抱闸检测时，驱动控制速度。此监控只有在抱闸自动检测时财有效 驱动监控抱闸电流，若未检驱动故障 自动恢复 抱闸测试时旋转马达或马达速度感应器 驱动故障 自动恢复 在抱闸测试时运行轿厢 驱动故障 自动恢复 断开抱闸连线，试图运行 40 - 95