The Finite Element Analysis of Connecting Rod of Diesel Engi

2021-02-21 08:04

柴油机连杆的有限元分析 英文资料

2010 International Conference on Measuring Technology and Mechatronics Automation

The Finite Element Analysis of Connecting Rod of Diesel Engine

Zhou Qinghui 1, Wang Yunying 2, Ji Wei2

1-Automobile Engineering Dept., Beijing University of Civil engineering and Architecture, Beijing, 100044, China,

2-Vehicle Engineering Dept. China Agriculture University, Beijing, 100083, China

qhzhou@http://www.77cn.com.cn

Abstract—Connecting rod mechanism is an important con-durability model of the ADAMS/View software. From this

sideration in the design of Diesel Engine. But it is difficult to we can clearly understand the stress-strain acting on each describe the dynamic changes of boundary conditions of the parts of the crankshaft and the connecting rod, quickly find running engine by the traditional method of simply finite dangerous position, and laid the foundation for the optimal element analysis. In order to obtain the vibration design of the mechanism.

characteristics and vibration frequency distributions, structural characteristics of the connecting rod mechanism using modal analysis is investigated. Firstly, a physical model of connecting rod mechanism is built using CAD software. Secondly finite element analysis and simulation of the model is taken by Hyperworks and MSC.Nastran softwares. Then its flexible multi-body dynamic model is established by ADAMS/View. And the fatigue stress of connecting rod under the max combustion pressure and Inertia force condition is calculated using the durability Module. The result indicates the stress distribution and deformation instance. The stress is mainly produced on the joint of connecting rod shell and the bottom end or the top end. And the biggest stress acting on the connecting rod is just 34.0613MPa, early smaller than its limited stress 355MPa. The method provides the theoretical evidence for connecting rod structure improvement and optimum design.

Keywords- connecting rod; finite element analysis; ADAMS;

II.

FINITE ELEMENT MODEL ING OF

CONNECTING ROD

I. INTRODUCTION

With the continuously strengthening of the engine, the working conditions of the connecting rod mechanism became more complex. In operation, the connecting rod is subjected to both gas pressure and inertia loads, and therefore, it must be adequately strong and rigid and light in weight as well. In order to improve the sufficient fatigue strength, stiffness, well static and dynamic mechanical properties under a variety of alternating load condition, it became a key question that how to even more base design decisions on virtual prototypes and to optimize the whole mechanism development process in recent years[1]~[3]. But it is difficult to describe the dynamic changes of boundary conditions of the running engine by the traditional method of simply finite element analysis. In order to study the mechanical properties of the connecting rod in the actual working conditions, the geometrical models of all the components of the connecting rod mechanism were founded with the CAD, the mass parameters were figured out. With using the software such as Hyperworks and MSC.Nastran, the crankshaft and the connecting rod were analyzed, and the model documents were created and transmitted into the ADAMS/View, and the fatigue stress brought by the eruptible power and the inertia force was analyzed with the

A. FEM equation of model analysis

The goal of modal analysis in structural mechanics is to determine the natural mode shapes and frequencies of an object or structure during free vibration. It is common to use the finite element method (FEM) to perform this analysis because, like other calculations using the FEM, the object being analyzed can have arbitrary shape and the results of the calculations are acceptable. The types of equations which arise from modal analysis are those seen in eigensystems. The physical interpretation of the eigenvalues and eigenvectors which come from solving the system are that they represent the frequencies and corresponding mode shapes. Sometimes, the only desired modes are the lowest frequencies because they can be the most prominent modes at which the object will vibrate, dominating all the higher frequency modes.

For the most basic problem involving a linear elastic material which obeys Hooke's Law, the matrix equations take the form of a dynamic three dimensional spring mass system. The generalized equation of motion is given as:

Mδ(t)′′+Cδ(t)′+Kδ(t)=P(t) (1) Where M is the mass matrix, δ(t)′′is the 2nd time derivative of the displacementδ(t)(i.e., the acceleration),

δ(t)′ is the velocity, C is a damping matrix, K is the

stiffness matrix, and P(t) is the force vector. The general problem, with nonzero damping, is a quadratic eigenvalue problem. However, for vibrational modal analysis, the damping is generally ignored, leaving only the 1st and 3rd terms on the left hand side:

Mδ(t)′′+Kδ(t)=0 (2)

Supposed that the solution of (2) is

δ(t)=δ0sinωt (3)

Then, (2) is taken the into (1), and

(K ω2M)δ0=0 (4)


The Finite Element Analysis of Connecting Rod of Diesel Engi.doc 将本文的Word文档下载到电脑 下载失败或者文档不完整,请联系客服人员解决!

下一篇:试论广播情感类节目主持人语言表现力的能动作用

相关阅读
本类排行
× 注册会员免费下载(下载后可以自由复制和排版)

马上注册会员

注:下载文档有可能“只有目录或者内容不全”等情况,请下载之前注意辨别,如果您已付费且无法下载或内容有问题,请联系我们协助你处理。
微信: QQ: