G3015激光切割机使用说明书
c: 程序实例释义: %
P062801 N2G71 N4G90
N20Q=P1 调入P1中设定的工艺参数子程序（如：P1=900303，则执行Q900303）
N30Q=P2 调入P2中设定的工艺参数子程序（如：P1=900313，则执行Q900313）
N60G10 N70M10
N75Q999997 N80G92X0Y0 N90G09
N100G160X1Y1Z1 N110G165F12
N220G0X60.526Y95.967
N230Q990053 切割层3（CUT3）工艺参数处理及准备
N240Q=P30 切割层3（CUT3）切割起始（开辅助功能及开光） N250G1X65.702Y76.648 N260X70.878Y95.967 N270X76.055Y76.648 N280X81.231Y95.967 N290X86.407Y76.648 N300X91.584Y95.967 N310X96.76Y76.648
N320Q=P31 切割层3（CUT3）切割结束（关辅助功能及关光） N330G0X24.859Y77.935
N340Q=P30 切割层3（CUT3）切割起始（开辅助功能及开光） N350G3X24.859Y77.935I1J0
N360Q=P31 切割层3（CUT3）切割结束（关辅助功能及关光） N370G0X33.359Y77.935
N380Q=P30 切割层3（CUT3）切割起始（开辅助功能及开光） N390G3X33.359Y77.935I2.5J0
N400Q=P31 切割层3（CUT3）切割结束（关辅助功能及关光） N410Q990039 切割层结束,切割头提升 N420G0X45.859Y77.935
N430Q990052 切割层2（CUT2）工艺参数处理及准备
N440Q=P20 切割层2（CUT2）切割起始（开辅助功能及开光） N450G3X45.859Y77.935I5J0
N460Q=P21 切割层2（CUT2）切割结束（关辅助功能及关光） N470G0X21.796Y36.232
N480Q=P20 切割层2（CUT2）切割起始（开辅助功能及开光） N490G1X21.796Y68.182
36
G3015激光切割机使用说明书
N500G3X21.235Y69.3I-1.536J-.071 N510X19.745Y69.258I-.714J-1.094 N520X19.702Y67.768I1.051J-.776 N530X20.821Y67.207I1.189J.975 N540G1X52.771Y67.207
N550G3X53.889Y67.768I-.071J1.536 N560X53.846Y69.258I-1.094J.714 N570X52.357Y69.3I-.776J-1.051 N580X51.796Y68.182I.975J-1.189 N590G1X51.796Y36.232
N600G3X52.357Y35.114I1.536J.071 N610X53.846Y35.156I.714J1.094 N620X53.889Y36.646I-1.051J.776 N630X52.771Y37.207I-1.189J-.975 N640G1X21.996Y37.207
N650Q=P21 切割层2（CUT2）切割结束（关辅助功能及关光）N660G0X77.261Y59.707
N670Q=P20 切割层2（CUT2）切割起始（开辅助功能及开光）N680G3X77.261Y59.707I2.5J0
N690Q=P21 切割层2（CUT2）切割结束（关辅助功能及关光）N700G0X92.261Y59.707
N710Q=P20 切割层2（CUT2）切割起始（开辅助功能及开光）N720G3X92.261Y59.707I2.5J0
N730Q=P21 切割层2（CUT2）切割结束（关辅助功能及关光）N740G0X77.261Y44.707
N750Q=P20 切割层2（CUT2）切割起始（开辅助功能及开光）N760G3X77.261Y44.707I2.5J0
N770Q=P21 切割层2（CUT2）切割结束（关辅助功能及关光）N780G0X92.261Y44.707
N790Q=P20 切割层2（CUT2）切割起始（开辅助功能及开光）N800G3X92.261Y44.707I2.5J0
N810Q=P21 切割层2（CUT2）切割结束（关辅助功能及关光）N820G0X102.261Y51.207
N830Q=P20 切割层2（CUT2）切割起始（开辅助功能及开光）N840G1X102.261Y37.207 N850X72.261Y37.207 N860X72.261Y51.207
N870Q=P21 切割层2（CUT2）切割结束（关辅助功能及关光）N880G0X72.261Y53.207
N890Q=P20 切割层2（CUT2）切割起始（开辅助功能及开光）N900G1X72.261Y67.207 N910X102.261Y67.207 N920X102.261Y53.207
N930Q=P21 切割层2（CUT2）切割结束（关辅助功能及关光）37
G3015激光切割机使用说明书
N940G0X74.234Y33.724
N950Q=P20 切割层2（CUT2）切割起始（开辅助功能及开光） N960G1X59.234Y7.743 N970X89.234Y7.743 N980X74.234Y33.724
N990Q=P21 切割层2（CUT2）切割结束（关辅助功能及关光） N1000G0X34.294Y5.743
N1010Q=P20 切割层2（CUT2）切割起始（开辅助功能及开光） N1020G1X34.294Y27.743 N1030X54.294Y27.743 N1040X54.294Y7.743 N1050X34.294Y7.743
N1060Q=P21 切割层2（CUT2）切割结束（关辅助功能及关光） N1070Q990039 切割层结束,切割头提升 N1080G0X32.195Y93.24
N1090Q990051 切割层1（CUT1）工艺参数处理及准备
N1100Q=P10 切割层1（CUT1）切割起始（开辅助功能及开光） N1110G1X32.295Y95.24
N1120G2X33.295Y96.239I1.311J-.313 N1130G3X33.295Y96.239I0J-5
N1140Q=P11 切割层1（CUT1）切割结束（关辅助功能及关光） N1150G0X52.195Y93.24
N1160Q=P10 切割层1（CUT1）切割起始（开辅助功能及开光） N1170G1X52.495Y95.24
N1180G2X53.295Y96.239I1.494J-.376 N1190G3X53.295Y96.239I0J-5
N1200Q=P11 切割层1（CUT1）切割结束（关辅助功能及关光） N1210G0X19.937Y.043
N1220Q=P10 切割层1（CUT1）切割起始（开辅助功能及开光） N1230G1X89.937Y.043 N1240X119.937Y52.005 N1250X89.937Y103.967 N1260X29.937Y103.967 N1270X-.063Y52.005 N1280X29.821Y.243
N1290Q=P11 切割层1（CUT1）切割结束（关辅助功能及关光） N1300Q990039 切割层结束,切割头提升 N1310M11
N410Q990037 切割结束,切割头回原点 N1330G0X0Y110 N1340G08 N1350M30 38
G3015激光切割机使用说明书
5.4.2.4工艺设定子程序说明
a:切割工艺参数子程序(例Q900303): %
P900303
N0303(3MM MILD)
*N10110 //===========CUT1====================================== *N10120 P100=5000 /...(5000).....FEEDRATE
*N10130 P101=3000 /...(3000).....W,CUT-POWER
*N10140 P102=95 /...(95).......0-100% OF MIN CUT-POWER *N10150 P103=1 /...(1)..........1-2,1=CW;2=GATE *N10160 P104=0 /...(0)..........0-7,PULSE FREQ *N10170 P105=0 /...(80)........0-99%,PULSE DUTY *N10180 P106=1.2 /...(1.2).......MM,CUT-HEIGHT *N10190 P107=2.0 /...(2.0).......BAR,CUT-PRESS
*N10200 P108=2 /...(2)..........1=AIR,2=O2,3=N2,CUT-GAS
*N10210 P109=1 /...(1)..........0=NOT, 1=USE;WHETHER TO LIFT *N10220 //===========PIERCE====================================
*N10230 P110=1 /...(1)...........0-3;0=NO;1=NORM;2=INC-F;3=FORCE *N10240 P111=1500 /...(2500)....W,PIERCE-POWER
*N10250 P113=1 /...(1)...........1-3,1=CW;2=GATE;3=SP *N10260 P114=2 /...(2)...........0-7,PULSE FREQ *N10270 P115=20 /...(20).........0-99%,PULSE DUTY *N10280 P116=1.5 /...(1.5)........MM,PIERCE-HEIGHT *N10290 P117=0.8 /...(0.8)........BAR,PIERCE-PRESS
*N10300 P118=2 /...(2)...........1=AIR,2=O2,3=N2,PIERCE-GAS *N10310 P119=500 /...(500).......MS,PIERCE-DELAY
*N10320 //======================================================
*N10330 P130=1 /...(1)..........0=NOT, 1=USE;WHETHER TO FOLLOW *N10340 P132=30 /...(30)........MM,Z AXIS LIFT HEIGHT *N10350 P133=100 /...(100)......1-100,%,DYNAMIC FACTOR *N10360 P134=500 /...(500)......MS,CUT-START-DELAY *N10370 P135=80 /...(80)........MS,CUT-FINISH-DELAY *N10380 P138=0 /...(0)...........MM,CUT FOCUS HEIGHT *N10390 P139=0 /...(0)...........MM,PIERCE FOCUS HEIGHT N10400M02
b:切割工艺参数子程序(例Q900313): %
P900313
N0313(3MM MILD)
*N10210 //===========CORNER=============================== *N10220 P170=1 /...(1)........0=DEC-DIS;1DEC-ENABLE *N10230 P171=80 /...(80).......%;PERCENT OF L-SPEED
39
G3015激光切割机使用说明书
*N10240 P172=50 /...(50)........MS;DELAY TIME
*N10110 //===========DOWN LEAD============================ *N10120 P120=0 /...(0)........0-2;0=NO;1=CUT-HOLE;2=DEC *N10130 P121=50 /...(50).......W,DOWN LEAD POWER *N10140 P122=1200 /...(50)......DOWN LEAD FEEDRATE *N10150 P123=1 /...(1)........1=CW;2=GATE
*N10310 P124=0 /...(0)........0-7,NO. PULSE FREQ *N10280 P125=20 /...(20)......0-99%,PULSE DUTY *N10160 P126=1.2 /...(1.2).....MM,CUT-HEIGHT *N10170 P127=2 /...(2)........BAR,CUT-PRESS
*N10180 P128=2 /...(2)........1=AIR,2=O2,3=N2,CUT-GAS *N10180 P177=100 /...(100)....% OF L-SPEED(DEC)
*N10190 P178=0 /...(0).........MM,DIST OF L-SPEED(DEC)
*N10200 P179=0 /...(0).........MM,NOZ-OFF OF L-SPEED(DEC) *N10250 //===========CUT2================================== *N10270 P140=4000 /...(4000).....FEEDRATE
*N10280 P141=2000 /...(2000).....W,CUT-POWER
*N10290 P142=90 /...(90).........% OF MIN CUT-POWER *N10300 P143=1 /...(1)..........1-2,1=CW;2=GATE
*N10310 P144=0 /...(0)..........0-7,NO. OF PULSE FREQ *N10280 P145=20 /...(20)........0-99%,PULSE DUTY *N10320 P146=1.2 /...(1.2).......MM,CUT-HEIGHT *N10330 P147=2.0 /...(2.0).......BAR,CUT-PRESS
*N10340 P148=2 /...(2)..........1=AIR,2=O2,3=N2,CUT-GAS
*N10340 P149=1 /...(1)..........0=NOT, 1=USE;WHETHER TO LIFT *N10350 //===========CUT3================================= *N10370 P150=2500 /...(2500).....FEEDRATE
*N10380 P151=1200 /...(1200).....W,CUT-POWER
*N10390 P152=90 /...(90).........% OF MIN CUT-POWER *N10400 P153=1 /...(1)...........1-2,1=CW;2=GATE *N10410 P154=0 /...(0)...........0-7,PULSE FREQ *N10420 P155=20 /...(20)........0-99%,PULSE DUTY *N10420 P156=1.2 /...(1.2).......MM,CUT-HEIGHT *N10430 P157=1.5 /...(1.5).......BAR,CUT-PRESS
*N10440 P158=2 /...(2)..........1=AIR,2=O2,3=N2,CUT-GAS
*N10440 P159=1 /...(1)..........0=NOT, 1=USE;WHETHER TO LIFT *N10450 //===========MAK4================================== *N10470 P160=8000 /...(8000).....FEEDRATE *N10480 P161=300 /...(300)......W,CUT-POWER
*N10490 P162=20 /...(20)........% OF MIN CUT-POWER *N10500 P163=1 /...(1)..........1-2,1=CW;2=GATE *N10510 P164=1 /...(1)..........0-7,PULSE FREQ *N10520 P165=20 /...(20)........0-99%,PULSE DUTY *N10520 P166=5 /...(5)..........MM,CUT-HEIGHT
40