元器件交易网http://www.77cn.com.cn
Absolute Maximum Ratings (1)
SymbolVTERM(VDD)VTERM(2)(VDDQ)
VTERM(2)
(INPUTS and I/O's)TBIAS(3)TSTGTJN
Rating
VDD Terminal Voltagewith Respect to GNDVDDQ Terminal Voltagewith Respect to GNDInput and I/O Terminal
Voltage with Respect to GNDTemperature Under BiasStorage TemperatureJunction Temperature
Commercial& Industrial -0.5 to 3.6 -0.3 to VDDQ + 0.3 -0.3 to VDDQ + 0.3
-55 to +125-65 to +150+1505040
UnitVVV
ooo
CCC
IOUT(For VDDQ = 3.3V)DC Output CurrentIOUT(For VDDQ = 2.5V)DC Output Current
mAmA
5666 tbl 06
NOTES:
1.Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation of thedevice at these or any other conditions above those indicated in the operational sectionsof this specification is not implied. Exposure to absolute maximum rating conditions forextended periods may affect reliability.
2.This is a steady-state DC parameter that applies after the power supply has reached its
nominal operating value. Power sequencing is not necessary; however, the voltage onany Input or I/O pin cannot exceed VDDQ during power supply ramp up.3.Ambient Temperature under DC Bias. No AC Conditions. Chip Deselected.
Capacitance (1)
(TA = +25°C, F = 1.0MHZ) PQFP ONLY
SymbolCIN COUT(3)
ParameterInput CapacitanceOutput Capacitance
Conditions(2)VIN = 3dVVOUT = 3dV
Max.810.5
UnitpFpF
5666 tbl 07
NOTES:
1.These parameters are determined by device characterization, but are notproduction tested.
2.3dV references the interpolated capacitance when the input and output switchfrom 0V to 3V or from 3V to 0V.3.COUT also references CI/O.
DC Electrical Characteristics Over the Operating
Temperature and Supply Voltage Range (VDD = 2.5V ± 100mV)
70T3519/99/89S
Symbol|ILI||ILI||ILO|VOL (3.3V)VOH (3.3V)VOL (2.5V)VOH (2.5V)
Parameter
Input Leakage Current(1)
JTAG & ZZ Input Leakage Current(1,2)Output Leakage Current(1,3)Output Low Voltage(1)Output High Voltage(1)Output Low Voltage(1)Output High Voltage(1)
Test Conditions
VDDQ = Max., VIN = 0V to VDDQVDD = Max., VIN = 0V to VDD
CE0 = VIH or CE1 = VIL, VOUT = 0V to VDDQIOL = +4mA, VDDQ = Min.IOH = -4mA, VDDQ = Min.IOL = +2mA, VDDQ = Min.IOH = -2mA, VDDQ = Min.
Min.
____________
Max.10±30100.4
___
UnitµAµAµAVVVV
5666 tbl 08
2.4
___
0.4
___
2.0
NOTES:
1.VDDQ is selectable (3.3V/2.5V) via OPT pins. Refer to p.5 for details.2.Applicable only for TMS, TDI and TRST inputs.3.Outputs tested in tri-state mode.